Assume a 3GHz processor executes three classes of instructions (A, B, C). i. Calculate the average CPI for this sequence of program. ii. Calculate the execution time for this sequence of program.

Q: Suppose that a task on the ARM computer runs 256M instructions during its execution. The total time…

A: Shortest Possible Stage time = 10ns Total execution time = 16M instructions * 1 cycle/inst * 10ns =…

Q: Let us assume we have a CPU which supports both 3-address and 2-address instruction. The length of…

A: 3 address:  Three-address instruction is a format of machine instruction. It has one opcode and…

Q: Let's assume that there are three processors, Pa, Pb, and Pc, like below. You can assume 1-way…

A: Instructions per second (IPS) = Clock rate / CPI

Q: Consider a pipeline that has 5 stages: (1) instruction fetch – 200 ps, (2) instruction decode - 100…

A: Answer is given below-

Q: Suppose on a non-pipelined single-processor machine, you have the following breakdown: alu…

A: (a)Non-pipelined single-processor machineAverage CPI = (0.25*2 + 0.3*10 + 0.15*4 + 0.3*1.5) = 4.55

Q: Show the execution of your program on the above pipelined processor for k = 6 by drawing a diagram.…

A: Assembly language program is defined as the low-level programming language for a computer or other…

Q: Q4. Consider a paging system with the page table stored in memory. Answer and explain the following.…

A: Computer operating systems employ paging, a memory management technique, to control and arrange the…

Q: Evaluate the effect of the instruction LDR r1, [r2], #4, given the initial values below. What is the…

A: As ldr r1,[r2], #4 means r1= mem[r2] this means r1=mem[1004] so r1=20 r2 = 1004+4 r2=1008  r3=50…

Q: A hardware designer is trying to choose between two code sequences running on the same computer. The…

A: The speed of a computer processor, or CPU, is determined by the Clock Cycle, which is the amount of…

Q: nis execution f g and without

A: Multi-programming is a process of loading several processes into memory simultaneously. When a…

Q: Question 3. A program is executed for 1 sec, on a processor with a clock cycle of 50 nsec and…

A: To calculate the CPI (cycles per instruction) for the program, we can use the following formula:…

Q: Processor X has 4 stages in its pipeline, namely, instruction fetch (IF), operand fetch(OF), operand…

A: solution:- given data: Total number of Stall cycles observed: 8 Cycles Given that, I1: ADD R2, R0,…

Q: Please help with the following questions and explain as much as possible please.

A: 1) In the absence of a pipeline: It would take seven cycles for each instruction to finish all seven…

Q: Modify the given machine below so that it supports the jr (i.e., jump register) instruction.…

A: Here explain you which control signal don't care. 1.RegDst=X don't care where the register to be…

Q: Consider two processors P1 and P2 with four types of instructions as listed in the table below.…

A: Given terms are: Dynamic Instruction count is 106 Processor P1 clock rate 2.0GHz and and Processor…

Q: Describe the events of each of the following instruction cycles as sequence of micro operations. The…

A: Question 1 The fetch cycle begins when the processor fetches the next instruction from memory. The…

Q: Consider a system with only two types of instructions, A and B. Type A instructions each require 7…

A: Given: Type A instructions each require (CPIA ) = 7 clock cycles Type B instructions each require…

Q: Consider a system that uses interrupt-driven I/O for a particular device which has an average data…

A: Interrupt I/O is a manner of controlling input/output pastime wherein a peripheral or terminal that…

Q: Consider the diagram below that shows the fetching data flow for an indirect cycle along with the…

A: What will be the content of the MAR register after finishing the execution of the indirect cycle for…

Q: With four parallel tasks, it may seem that four cores will give the best speedup over sequential…

A: Parallel Processing is a method that helps the computer system to run two or more processors…

Q: 2. Create a new asm project “Lab2_Q2.asm". Assume that port B 8255A PPI is the source for 256 bytes…

A:

Q: If interrupt synchronization is turned off, it must be turned back on before leaving a critical…

A: Disabling interrupts on the CPU in a multiprocessor system prohibits other programmes from running…

Q: Multicycle execution is better than single cycle execution since it is: a. Every operation is…

A: 9)The correct answer is b. Break up operation so that each stage is executed in 1 clock cycle and…

Q: 1. When a program is adapted to run on multiple cores in a multiprocessor system, the execution time…

A: Here is the complete solution of the above problem. See below steps.

Q: Assume that your program has 2400 memory accesses in 20,000 instructions. The instruction cache miss…

A: Answer: (B)Explanation: Since, L2 cache is shared between Instruction and Data. Average Instruction…

Q: 1. When a program is adapted to run on multiple cores in a multiprocessor system, the execution time…

A: Here is the explanation of the above problem. see below steps.

Q: This is a three-part question about critical path calculation.  Consider a simple single-cycle…

A: Here is solution of Question 1 Part A.Please find in below steps.

Q: Q3. “There is a mechanism in which CPU relinquishes the control over the buses for carrying out…

A: DMA (Direct Memory Access): In the Direct Memory Access, the inter-face transmits the…

Q: f. Compare the actual speedup factor provided by Machine C over Machine B with the theoretical…

A: To calculate the speedup factor provided by Machine C over Machine B, it needs to consider the…

Q: An 8-bit data is read from an input device and stored in the memory location 0x20000200. This data…

A: Assembly instructions: MOV This instruction copies the source operand value to destination register.…

Q: Explain why it is not feasible to keep up with the growth of Moore's Law by constantly adding more…

A:

Q: Suppose we have a four (4) core processor and all processes are designed to be multi-threaded. Now,…

A: Kernel threads:- A kernel thread is an entity that handles the system scheduler, like processes and…

Q: memory range from 0xA000 to 0xCFFF (inclusive) Your design must be subject to the followi

A: The system has 3 microprocessors and shared memories are there for all the processors. there will be…

Q: Is it still feasible to accomplish pipelined execution even if the time it takes to execute pipeline…

A: Explanation Pipelining does not assist with a single task delay, but it does help to complete the…

Q: Translate the following user-level instruction to a microprogram so it can be directly executed by…

A: Hey there, I am writing the required solution of the above stated question.Please do find the…

Q: You are part of the CPP team tasked with designing a new processor. This processor operates at a…

A: Determine the percentage of each instruction type:Instruction Class A makes up 50% of all…

Q: Assume that your program has 2400 memory accesses in 20,000 instructions. The instruction cache miss…

A: Answer: (B)

Q: True/False Run times of the typical five stages to execute an instruction are as given in some…

A: Here in this question we have given five stage  Instruction Fetch: 10 Instruction Decode: 15…

Q: B. For the following 8085 assemble code, calculate the total execution time 0100: LXI D,1000H 0103:…

A: Way to compute execution time:   The internal clock frequency of the 8085 MPU is 3MHz if the…

Q: the clock frequency of CPU A is 8MHz, how long is one clock cycle of CPU A? b) If the CPU A can…

A: a) One clock cycle of CPU A is 0.125 milliseconds (1/8 MHz = 0.125 milliseconds). T=1/f   b) The…

Q: Consider a 32-bit microprocessor, with a 16-bit external data bus, driven by an 8-MHz input clock.…

A: