An over dried soil mass of 200 gm is placed is pycnometer and completely filled withwater. Combined mass of bottle, soil and water is 1605 gm. Calculate specific gravityof soll if pycnometer with water alone has weight of 1480 gm:-

Given : Oven dried soil mass = 200 gm Mass of soil + bottle + water = 1605 gm Weight of pycnometer…

An over dried soll mass of 200 gm is placed is pycnometer and completely filled wi water. Combined mass of bottle, soll and water is 1605 gm. Calculate specific grav of soll if pycnometer with water alone has weight of 1480 gm:-

An over dried soll mass of 200 gm is placed is pycnometer and completely filled wi water. Combined mass of bottle, soll and water is 1605 gm. Calculate specific grav of soll if pycnometer with water alone has weight of 1480 gm:-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2 - Two concentric cylinders are covered by a rigid plate that carries an axial load, as shown in…

A: Rise in temperature, T

Q: How much bleaching powder is needed to chlorinate 5000l of water whose chlorine demand is 2 mg/l,…

Q: The specific gravities of solids and carrier fluids of a slurry are usually known, but the specific…

A: Specific gravity is defined as the ratio of the density of solids in the slurry and the density of…

Q: determine the specific weight density and specific gravity if a liquid thar occupies vol.if 200l and…

A: Mass of the liquid M =178 Kg Weight of that particular liquid will be W = Mg = 178 x 9.81 =1746.18 N…

Q: Calculate the total mass of concrete required to construct the dam shown below. Concrete has a…

A: To determine the mass of concrete required to construct the dam. Given, Density of concrete (ρc) =…

Q: In ratio of 3:2 between alcohol and water is to be mix in order to produce a 1000 ml ethyl alcohol.…

Q: A 950 me soda bottle weights 775 gram when ît is filled with sodo and 30 grams when empty. Determine…

Q: After fracture, the total length was 53.086 mm and the diameter was 9.982 mm. Plot the engineering…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Relative roughness, eD 当 64/Re at now Darey friction factor, FIGURE Q3(d) 100000 H1000000=gP…

Q: Fluid Mechanics I tried to get a jar of Mexican chocolate mole' sauce through an airport TSA officer…

A: We have been given the following information,Density of Mexican chocolate mole sauce = 7000…

Q: A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and…

Q: QUESTION # 2 A brass cube 6 in on a side weighs 67 Ib. We want to hold this cube in equilibrium…

Q: In constructing dams, the concrete is poured in lifts of approximately 1.8 m (y₁ = 1.8 m). The forms…

A: y1=1.8 mAssume that the moment will occur at the base be: MMoment = Force Distance

Q: 4. A brass weight is to be attached to the bottom of the cylinder so that the cylinder will be…

Q: A rubber block is placed between two rigid walls where a load of P = 65 kN is applied on top as…

A: Given data P = 65 KN

Q: Two sphere, each 1.5m in diameter weighs 7KN and 20KN respectively. They are connected with a short…

Q: 2. A simply supported bean is loaded as shown in the figure below. Compute the beam bending moment…

Q: Calculate the R-value for the following materials:a. 100 mm thick brickb. 10 cm thick brickc. 30 cm…

A: The formula for R-value is given by, R-value=LK Where, L = thickness K = thermal conductivity

Q: etermine the weight of water in grams.

Q: - The water velocity near the river surface is 6 ft/s, and the pipe inlet is placed in th al to the…

Q: Shaping losses Ingredients Mixer Shaper Fryer Steam oven Freezer → Falafel The figure shows parts of…

A: Shaping losses Ingredients → Mixer→ Shaper → Fryer → Steam oven →…

Q: A Brine containing 2 lb of salt per gallon runs into a tank at 2 gal/min, brine from this first tank…

A: The figure is shown below,

Q: PROBLEM 4: The tank contains a liquid having a density as shown. 0.82 ft 10 ft 5 ft 7 ft Pliquid =…

A: (a) multiplying the density by "g" acceleration due to gravity to obtain the unit weight Unit…

Q: Which length shall I use to calculate current density: the whole bar length or the embedded length…

A: Answer embedded length is known as the length of the embedded steel reinforcement, The embedded…

Q: Q57: In Figure below, calculate Fx and Fv per unit width of the cylinder cylinder Water

A: assume the width of the the curved surface is unit (i.e.=1 m). force in the horizontal direction is…

Q: cure 1 of 1 D 60° 4m If load C has a mass of 380kg, determine the required minimum diameter of the…

Q: 2. A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and…

Q: A concrete column has a diameter of 350 mm and a length of 2m. If the density (mass/volume) of…

A: Given :-Diameter of the column = 350 mm Length of the column = 2 m Density (mass/volume) of concrete…

Q: VOLUME Va cm Vw= cm VT-295 cm3 water content= porosity void ratio= saturation Total density (g/cm³)…

Q: Determine the total mass of solids removed over the entire 8-hour period, in kg.

A: A table is shown in the given figure as need to findThe total mass of solids removed over the entire…

Q: 7000 lb 5000 lb 6000 lb 4000 lb 3 ft 5 ft 4 ft

A: Series of load acting on aluminium bar is given and it has been asked to determine elongation of the…

Q: 3. What is the diameter change of a 50-ft spherical tank made of ½" steel plate due to internal…

A: Internal diameter = 50 ft. wall thickness = t = 0.5'' v = 0.3. p = 100 psi. E = 30,000,000 Psi.

Q: Example: Copper Material Distance between anchor= 100 mm L = Im h = 6.5mm, b = 25.5 mm I…

A: Given data: Distance between the anchor = 0.1 m L= 1m h=6.5 mm b= 25.5 mm I=583.6 mm4. Y=3.25 mm

Q: 2. A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and…

Q: 2: Your alloy contains 60% Ag and is at temperature 778.9°C a) Hypoeutectic or Hypereutectic? b)…

A: Given data, alloy contains =60% Ag = WAg Temperature=T=778.9˚c( just below…

Q: 17. Which one of the following units is equivalent to a Joule? Select one •a kgms b kg m's • ckgms…

A: joule is the SI unit of work or energy and is also equal to the work done by the force of newton.it…

Q: A wooden cylinder with 660mm diameter, length of 1300mm and specific gravity of 0.61 is placed…

A: Given: The diameter of the cylinder is 660 mm. The length of the cylinder is 1300 mm. The specific…

Q: A blacksmith immersed a piece of steel at 600°F into a large bucket of water with a temperature of…

A: (1) Initial temperature of steel(2) Water temperature(3) After temperature of steel

Q: lock of wood requires a force of 40N downward to keep it fully immersed in water and a force of 100N…

A: To find volume of wood

Q: The coefficent of static friction between the crate and the floor is u, = 0.5. (Figure 1) Part A…

A: Solution Given Data Coefficient of static friction μs=0.5 Draw the FBD

Q: A cylindrical can is to be made to hold 1 liter of oil. Find the dimensions (in cm) that will…

Q: The following information is given for n-pentane at 1 atm:boiling point = 36.20°C ΔHvap (36.20°C) =…

A: A type of elastic collision in which two objects of equal mass initially move in the same direction…

Q: Adding 20ml sample to a 300ml DO bottle causes its dissolved oxygen concentration to decrease by 10…

Q: raudon. - A water contains 200 mg/L Ca, 75 mg/L Mg, 180 mg/L HCO3, and 150 mg/L. CO₂, all expressed…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

An over dried soil mass of 200 gm is placed is pycnometer and completely filled with
water. Combined mass of bottle, soil and water is 1605 gm. Calculate specific gravity
of soll if pycnometer with water alone has weight of 1480 gm:-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(Same given conditions as the previous problem) Convert one hr UH to 2 hr UH. What is the value of "C" in the table? time (hr) 0 0.5 1 1.5 2 2.5 3 3.5 1-hr UH, cfs 0 32 44 52 36 22 10 O 2-hr UH, cfs 0 A B CO С
Calculate the reaction Use 3 decimal places Base your calculation to the incomplete solution
Answer the following: 1. Aggregates property that relates to the particle's ability to take in a liquid. 2. An investigation or trial to ascertain the true characteristics of a material/s. 3. Aggregates with diameter of 3 inches to 6 inches. 4. A mass formed by union of distinct but similar materials. Refers to granular mineral particles. 5. Used to examine materials and components in ways that do not harm the future usefulness and service of the material. 6. _________is the ratio between the Net weight of the aggregates to the volume.
Calculate the percent passing by starting with 100% and subtracting the percent retained on each sieve as a cumulative procedure: total mass=500g. Mass retained on No.4sieve=9.7g. Mass retained on No.10 sieve=39.5 g
A 450 mm diameter ice sphere with 0.56 ft³/slug specific volume, melts and filled a cubic container. Determine the edge of the cube in inches.
Figure P2.33 shows a portion of the H,O-NaCl phase diagram. 10 Liquid (brine) Salt Ice + -10 F liquid (brine) liquid (brine) -20 Ice + salt -30 NaCI 10 20 30 H2O 100 90 80 70 FIGURE P2.33 Composition, weight % a. Using the diagram, briefly explain how spreading salt on ice causes the ice to melt. Show numerical examples in your discussion. b. At a salt composition of 10%, what is the temperature at which ice will start melting? c. What is the eutectic temperature of the ice and salt combination? Temperature, °C
What is the molar concentration of 196 mg/L sulfate acid (H2SO4)? Use mol/L or mmol/L as the unit in your final result.
Check my w A solid block, of specific gravity 0.93, floats such that 75% of its volume is in water and 25% of its volume is in fluid X, which is layered above the water. What is the specific gravity of fluid X?
Problem 3.25 The acrylic plastic rod is 200 mm long and 25 mm in diameter. Figure 1 of 1 -200 mm- Part A If an axial load P of 400 N is applied to it, determine the change in its length. Ep =2.70 GPa, vp = 0.4. (Figure 1) Express your answer with the appropriate units. 8 = Submit Part B μÃ Ad= Value Submit Incorrect; Try Again; 4 attempts remaining Units My Answers Give Up Determine the change in its diameter. Express your answer with the appropriate units. μA Value Units ? My Answers Give Up ?
A 0.5 m ice cube with 0.56 ft^3/slug specific volume, melts and filled a spherical container. Find the radius of the container in inches.
A liquid has an absolute viscosity of 3.2 × 10¬* Ib-sec/ft?. It weighs 56 Ib/ft³. What are its absolute and kinematic viscosities in SI units?
Sieve Apperture (um) Weight Retalned, (g) Weight of ore = 500 g 200 150 -125 100 75 45 30 100 50 What is the percentage composition material between 200 and 180 um? 68 80 Were there some material losses? What 20 60 100 20 accounts for such an observation? Pan