An inverted cone is placed in a water tank as shown below. If the weight of the cone is 46 N, what is the tensile force in the cord connecting the cone to the bottom of the tank? 100 cm 25 cm 50 cm Water Cord

Q: Q5: At the instant shown in figure (5) 04 = 6 rad/s, pulley A is given an angular acceleration a =…

A: Given data: The radius of the pulley A is rA=60 mm=0.06 m The initial angular velocity of the pulley…

Q: Impact velocity equation

A:

Q: Which of the following part designs would be preferred because it would result in lower production…

A: To be explained:- which method will give lower cost

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is three The tolerance is determined by the function.

Q: ADD MISSING LINES (VISIBLE OR HIDDEN) TO EACH OF THE PROBLEMS BELOW. XX * 30

A: Given: Photographic views: Top view, Front View and Right View.To draw: Missing lines for each…

Q: Indicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle…

A:

Q: Statics; working

A:

Q: - Rz (Ten-point surface roughness, The mean and valleys of distance b/us five Over a Wavines: ·Lay:…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: Find the following. Show complete solution.

A: The given diagram is here, Section 1:- A rectangle OABC, whose sides are 120 mm and 80 mm Section…

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: I need help matching the parts of the print to the terms.

A: Tolerance block will go with choice E.

Q: What is angular indexing and block indexing?

A: Angular indexing:  It is similar to simple indexing except that in this process, instead of rotating…

Q: A datum when used in manufacturing is primarily used for?

A: A datum in manufacturing is defined as the origin point, plane, or axis from which the geometric…

Q: Limit Gauge loose fit, slide fit, easy sliding fit, running fit Go & No Go Ends O the difference…

A: As per our guidelines we are supposed to answer only one question if multiple questions are asked.…

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2.  There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: What do the Discontinuity functions express?

A: A discontinuity function expresses that at the point of discontinuity either the limit doesn’t exist…

Q: what happened with the 10 in the first equation?

A:

Q: Determine, using the principle of superposition, the reactions at supports A and B for equilibrium.…

A:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: General Questions Not Directly Related to the Print 1.  A ________ print is a supplemental print…

A:

Q: The part view should.com RANCES be the same CHD APPVD MIG GA as picture. 2- The color is RGB as DWG…

A: Find Draw the given object using the drawing.

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: On the attached drawing, is the allowance between "shaft C" and "hole D" positive or negative?

A: Allowance is the difference between the basic dimensions of the mating parts. There are two types of…

Q: OA F >F>F OE- F = F, F, >F, >F, F > F, >F, D) OF> F >F,

A: Forces on the surfaces, F1,F2,F3 Area of each surfaces, 2S,S,3S

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: Q2 (a) Figure Q2 (a) shows two vectors FA and Fa represent the forces exerted on the pulley by the…

A:

Q: Material is forced through a die opening called Drawing Select one: OTrue O False

A: A metals working process in which the material is forced through a die such as metal, glass of the…

Q: What is rectification

A: Rectification is the conversion of alternating current to direct current. Rectification is performed…

Q: 15. On the produced part below, show a simple sketch on how the flatness on the part m verified and…

A: Flatness:- It is defined as the minimum distance between two planes within which all the points on…

Q: Find the taper angle, in radians, for a workpiece if a sine bar method was used. The stacked height…

A: Sine Bar is used to measure taper angle by using gauge lengths and length of sine bar. It is the…

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: What is called the fit? 1) the difference between the maximum and minimum limits of size, 2) the…

A: Handwritten.jpg

Q: What company specification number is given to the material for this part?  2. What is the revision…

A: Engg drawing is a technical drawing that is used to transfer the information from the design to the…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.