An eight meter simply supported beam carries a superimposed dead load of 6kN/m and a service live load of 15kN/m. The beam has a width and total depth of 400mm and 550mm respectively. It is reinforced with five diameter 25mm bars and 10mm stirrups. Material properties are fc'=27.60MPA and fy=421.60MPA. A. Using the detailed calculation of Vc, determine the nominal shear strength of concrete at 0.60m from the support. B. Using the detailed calculation of Vc, determine the shear carried by stirrups at 0.90m from the support.

An eight meter simply supported beam carries a superimposed dead load of 6kN/m and a service live load of 15kN/m. The beam has a width and total depth of 400mm and 550mm respectively. It is reinforced with five diameter 25mm bars and 10mm stirrups. Material properties are fc'=27.60MPA and fy=421.60MPA. A. Using the detailed calculation of Vc, determine the nominal shear strength of concrete at 0.60m from the support. B. Using the detailed calculation of Vc, determine the shear carried by stirrups at 0.90m from the support.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B4
Provide complete and neat solution
Title: Design of Beam in Flexure (WSD Method) PROBLEM: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 mm. Take b = d/2. Use WSD method. As C6omm 20 KN lo KN/m 8 KN/m 5m 3m
The allowable shear stress is τallow=895 psi�allow=895 psi. The supports at A� and B� are smooth
What advantages does the automated method have over the manual method?
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
Title: Design of Beam in Flexure (WSD Method) PROBLEM: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 mm. Take b = d/2. Use WSD method. As (Gomm 20 KN lo Ka/m 8 KN/m 3m
A 300mm x 500mm rectangular concrete beam is reinforced with four pieces 25mm diameter bars. The beam is simply supported on a span of unknown length. The uniform linear dead load from the slab is 18KN/m (weight of beam not included) and the uniform linear live load is 10kN/m. The effective depth of the beam is 430mm. the beam. Use area of one 25mm diameter bar = 510mm2. Using your own values of fc' = 20.1 MPa and fy = 335 MPa from the excel file, determine the safe length
a.what is the maximum bending stress fbx (MPa) in the girder b.determine the maximum bending stress fby (MPa) in the girder c.using interaction formula fbx/Fbx + fby/Fby
Determine the maximum safe service live load that the beam can carry if the service dead load is 12 kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40 MPa and fy=415 MPa. Top bars are 6-32mm and bottom bars are 3-28 mm, center to center distance between the bar layers is 108mm. 70 mm 108 mm 352 mm 7.2 mm 6.7 mm B A 70 mm 300 mm
Answer 15&16