A 300mm x 500mm rectangular concrete beam is reinforced with four pieces 25mm diameter bars. The beam is simply supported on a span of unknown length. The uniform linear dead load from the slab is 18KN/m (weight of beam not included) and the uniform linear live load is 10kN/m. The effective depth of the beam is 430mm. Using your own values of fc' = 20.1 MPa and fy = 335 MPa from the excel file, determine the safe length of the beam. Use area of one 25mm diameter bar = 510mm?.

A 300mm x 500mm rectangular concrete beam is reinforced with four pieces 25mm diameter bars. The beam is simply supported on a span of unknown length. The uniform linear dead load from the slab is 18KN/m (weight of beam not included) and the uniform linear live load is 10kN/m. The effective depth of the beam is 430mm. Using your own values of fc' = 20.1 MPa and fy = 335 MPa from the excel file, determine the safe length of the beam. Use area of one 25mm diameter bar = 510mm?.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A reinforced beam has a: width = 500 mm effective depth = 600 mm n = 9 If the maximum stress of 5 MPa is developed in the concrete when resisting a moment of 80 kN-m. What stress is developed in the steel. What area of reinforcing steel is required?
A rectangular concrete beam has a width of 290 mm and an effective depth of 550 mm. The beam is used to carry a factored moment load of 460 kN-m. Assume fc = 21 MPa and fy = 276 MPa, reduction factor = 0.9. Determine the minimum tension steel area for singly reinforced concrete.
INELASTIC BENDING OF SINGLY REINFORCED CONCRETE BEAM SECTION *A trapezoidal concrete beam is casted with a compressive strength of about 20 MPa. The beam is reinforced with 3- 32 mm diamater bars in the tension zone with a yield strength of 275 MPa. The bar is located 100 mm from the bottom. Determine the nominal bending strength. Assume that the beam is symmetrical about the vertical axis with a depth of 600 mm, a top width of 500 mm, and a bottom width of 200 mm.
A reinforced concrete beam having a width of 300mm and a overall depth of 600 mm is reinforced with 2-25mm compression bars placed 60 mm from extreme concrete & 6-25mm tension bars with concrete covering of 60 mm from the centroid of the bar group. Concrete Strength, fc' = 27 MPa, Steel Strength, fy = 415 MPa. A. Determine the balanced steel area considering the contribution of the compression steel. B. Determine the maximum tension steel area allowed by the code.
The beam is loaded uniform deadload of 42 kN/m (including its own weight), and a uniform live load of 48 kN/m. Concrete strength fc' = 21 MPa and steel yield strength fy = 415 MPa, concrete cover is 65 mm from the centroid of the bars. Assume El to be constant. 320 mm 540 mm 7m 2m a. What is the uniform factored load on the beam in kN/m? b. What is the vertical reaction (factored) at B in KN? c. What is the maximum nominal moment can the beam carry if it is to be design as singly reinforced, in kN.m? d. What is the required tension steel area in mm2, at point of maximum positive moment? e. What is the required tension steel area in mm2, at point of maximum negative moment? f. Using simplified calculation, calculate the nominal shear strength provided by concrete near the fixed end, in KN? g. Using 10 mm W-stirrups with fyh = 275 MPa, what is the required stirrup spacing near the fixed end?
As shown in the figure, a 3m-long cantilever beum is subjected to a uniformly distributed dead load, we-1.S t/m. It is know that f = 20MP. fy =420 MPa, and 4, = 1800 mm. Please find the maximum allowable uniformly distributed live load, wt is assumed that the unit weight of concrete is we24 t/m. -300m-
Problem #1. The base of a rectangular reinforced concrete beam is 300mm and the effective depth is 550mm. Concrete compressive strength on the 28" day is 24MPA and steel yield strength is 415MP.. Determine : a. The depth of compression block (in mm, 2 decimal places), the strain in the tension steel (5 decimal places) and ultimate moment capacity (in KN.m, nearest tenth) of the beam if it is reinforced with 4-32mm diameter bars. b. The depth of compression block, the strain in the tension steel and ultimate moment capacity of the beam if it is reinforced with 4-20mm diameter bars.
Check the capacity of the plain concrete beam having span of 20ft. A load of 2.0 kip/ft is applied on beam. The beam has width = 12” and depth = 20”. Concrete compressive strength (fc′) = 3 ksi
Problem The following are the dimensions of a concrete T-beam section Width of flange, bf = 600 mm Thickness of flange, tf = 80 mm Width of web, bw = 300 mm Effective depth, d = 500 mm The beam is reinforced with 3-32 mm diameter bars in tension and is carrying a moment of 100 kN.m. Find the total compressive force in the concrete. Use n = 9.
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored liveload in Kilo Pascals? Express your answer in 2 decimal places
A 6m long simply supported reinforced concrete beam has a width of 350mm and an overal1 depth of 470mm. The beans is reinforced with 2-28mm compression bars and 4-28mm tension bars, each located 70mm from the extreme fibers. Concrete strength f'c = 20. 7 MPa, and steel yield strength fy=415 MPa. Determine the ff: 1) Depth of compression block assuming both tension and compression steel yields. 2) what is the ultimate moment capacity of the beam in KN.m. 3) Determine the additional concentrated live load that can be applied at midspan if the dead load including the weight of the beam is 20KN/m. Use Mu=1.2Mdl+1.6M11 (Based of NSCP 2015) Show complete solution and neat handwriting. Use NSCP 2015.
A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa 10. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = mm (2 decimal places) 11. What is the condition of failure? = (Balanced, Tension controlled, Compression controlled, Transition) 12. Calculate the design moment strength of a typical interior beam. = kN⋅m (whole number)