1%9. l. In.• f 10 Y:-quiz2.pdf >Quiz: Design the reinforcement steel that necessary for the shcar and torsion forthe rectangular cantilever beam shown in figure. Use for stirrups (o12) and letf.=25 MPa, f-400 MPa, dead load (5 kN/m?) and live load (10 kN/m), take intoaccount the self-weight of beam. All dimensions in (mm)10008003000300Cnand TEXTEDTII

Solution; Given that; Live load=10 KN/m2Dead load =5 KN/m2fck=26MPafy=400 MPa

Quiz: Design the reinforcement steel that necessary for the shear and torsion for the rectangular cantilever beam shown in figure. Use for stirrups (12) and let f-25 MPa, f-400 MPa, dead load (5 kN/m²) and live load (10 kN/m²), take into account the self-weight of beam. All dimensions in (mm) 1000 800 3000 300 Chmeand 001

Quiz: Design the reinforcement steel that necessary for the shear and torsion for the rectangular cantilever beam shown in figure. Use for stirrups (12) and let f-25 MPa, f-400 MPa, dead load (5 kN/m²) and live load (10 kN/m²), take into account the self-weight of beam. All dimensions in (mm) 1000 800 3000 300 Chmeand 001

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam cross-section shown is design to resist a nominal moment M₁ of 320 kN m, if f = 35 MPa and fy = 420 MPa, determine the required area of steel reinforcement Ag. 75,75,75 As 225- 75 565 60 700mm 0.85f I N2 0.85f d 1-17/22 T₁ T = T₁+T₂ d C₂ a-75 I a-75 2 T₂
Do not use chat gpt
PLEASE INCLUDE COMPLETE FIGURES
F1 Determine the reaction forces for girder G-1. Column A Beam B-1 L1 -0 Beam B-2 F2 Girder G-1 Please round to the nearest one. Reaction force for Girder G-1 (Column A side) = Girder G-2 L1 After the initial calculation, we determined the following information: • The reaction force for Beam B-2 (Girder G-1 side) = 17,890 lbs • The reaction force for Beam B-3 (Girder G-1 side) = 15,685 lbs Reaction force for Girder G-1 (Column B side) = 80 F3 • Live load 50 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 10 psf, (3) Mechanical equipment = 8 psf, (4) Suspended ceiling = 8 psf (5) Beam = 25 lb/ft, (6) Girder = 35 lb/ft • Beam and Girder spacing:: (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Beam B-3 000 000 F4 lbs open lbs F5 L1 Column B Beam B-4 L2 F6 L3 MacBook Air ← F7 F8
concrete : C20 steel: S420 h=550 mm b=350mm steel rebars : 5Φ18
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy = 345MPA Select the correct response: MII = 244.02KN-m MII = 390.43KN-m %3D MII = 666.43KN-m MII = 436.43KN-m
Question 17
span of beam af is 6 meters. Thank you.
Plz, solve this problem using Flexibility method and show all the steps one by one and draw SFD and BMD Structural Analysis-2
DO NOT ROUND OFF IN BETWEEN SOLUTIONS.