3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPa. Aluminum Bronze A = 400 mm Steel A = 200 mm? A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m

3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPa. Aluminum Bronze A = 400 mm Steel A = 200 mm? A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 102 GPa] with a cross-sectional area of A₁ = 200 mm². Bar (2) is an aluminum alloy [E = 72 GPa] with a cross-sectional area of A₂ = 640 mm². All bars are unstressed before the load P is applied; however, there is a 2-mm clearance in the pin connection at A. Assume L₁ = 1880 mm, a = 1060 mm, b = 620 mm, c = 480 mm, and L₂ = 1270 mm. If a load of P = 71 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. (1) L₁ b tc B (2) D L2
E 0.4m D 10KN 0.8m 0.4m В 5KN 0.6m Al 20KN A=800 mm? A=1,200 mm?
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
If length of rod is 2 m and a radius of 20 mm is made of high-strength steel. The rod is subjected to a torque T, which produces a shear stress below the proportional limit. If the cross section at one end is rotated 45 degrees in relation to the other end, and the shear modulus G of the material is 90 GPa, calculate the amount of applied torque?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm
Narrow bars of aluminum are bonded to the two sides of a thick steel plate as shown. Initially, at T₁ = 70°F, all stresses are zero. Knowing that the temperature will be slowly raised to T₂ and then reduced to T₁, determine (a) the highest temperature T₂ that does not result in residual stresses, (b) the temperature T₂ that will result in a residual stress in the aluminum equal to 58 ksi. Assume aa = 12.8 x 10-6/°F for the aluminum and a = 6.5 × 10-6/°F for the steel. Further assume that the aluminum is elastoplastic with E = 10.9 × 106 psi and ay = 58 ksi. (Hint: Neglect the small stresses in the plate.) Fig. P2.121