An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure P-108. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPA, or in bronze of 100 MPa. Steel A = 500 mm 2 Aluminum Bronze %3D A 400 mm2 4 200 mm 4P 2P ure P-108 E2.5 m 2.0 m 1.5 m-

An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure P-108. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPA, or in bronze of 100 MPa. Steel A = 500 mm 2 Aluminum Bronze %3D A 400 mm2 4 200 mm 4P 2P ure P-108 E2.5 m 2.0 m 1.5 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; a = 12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; a = 9.6 x 10-6/°F] bar with a width of 2.0 in. and a thickness of 0.75 in. The supports at A and C are rigid. Determine (a) the lowest temperature at which the two bars contact each other. (b) the normal stress in the two bars at a temperature of 250°F. (c) the normal strain in the two bars at 250°F. (d) the change in width of the aluminum bar at a temperature of 250°F. (1) 3.0 in. 32 in. 2.0 in. B ↓ (2) 44 in. 0.04-in. gap Determine the lowest temperature, Tcontact, at which the two bars contact each other.
A tensile force P Newton is applied gradually on a prismatic bar of length L m and areas of cross- section A m². The strain energy stored in the bar will be equal to
#2 will upvote to anyone who will answer
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the brass. Steel Brass Copper Est = 200 GPa 12(10-)/°C apr Ebr Ecu 17(10-)/°C 120 GPa 100 GPa %3D ast = 21(10-6)/°C acu Acu = 515 mm? |Ast 200 mm2 Abr = 450 mm2 300 mm -200 mm 100 mm O -0.0109mm O 0.0241mm O -0.0241mm O 0.0109mm oooO
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.5 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.7 in. and a thickness of 0.75 in. The supports at A and C are rigid. Assume h1=2.5 in., h2=1.7 in., L1=31 in., L2=46 in., and Δ=Δ= 0.04 in. (A) Determine the lowest temperature, Tcontact, at which the two bars contact each other. (B) Find a geometry-of-deformation relationship for the case in which the gap is closed. Express this relationship by entering the sum δ1+δ2, where δ1 is the axial deflection of Bar (1), and δ2 is the axial deflection of Bar (2). δ1+δ2= _____in. (C) Find the force in the Bar (1), F1, and the force in Bar (2), F2, at a temperature of 225oF. By convention, a tension force is positive and a compression force is negative. IN KIPS (D) Find σ1 and σ2,…
The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is steel [E = 200 GPa; a = 11.7x 10-6/°C], with a cross-sectional area of A1 = 370 mm2. Bar (2) is an aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C], with a cross- sectional area of A2 = 380 mm?. The bars are unstressed when the structure is assembled. Assume a=360O mm, b=620 mm, c=730 mm, P=20 kN, and L=890 mm. After a concentrated load of P = 20 kN is applied and the temperature is increased by 35°C, determine (a) the normal stresses in bars (1) and (2). (b) the deflection of point D on the rigid bar. A (1) B (2)
Problem # 2. At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 140 °C, determine (a) the normal stress in the aluminum rod Ans: A -300 mm Aluminum A = 2000 mm² E = 75 GPa α = 23 x 16-6/°C 0.5 mm -250 mm Stainless steel A = 800 mm² B E = 190 GPa a = 17.3 x 10-6/°C
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown below. Axial loads are applied at the positions indicated. Find the maximum value of P in Newton that will not exceed a stress in steel of 150 MPa, in aluminum of 87 MPa, or in bronze of 97 MPa.
In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is oal = -90 MPa and the initial temperature 20°C. 2) The final length of the aluminium member. Aluminum A=1800mm? E=73GPA Bronze A=1500mm2 E=105GPA a=23.2x10-6/°C a=21.6x10-6/°C Gap=0.5mm 0.35m 0.45m
Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
simple strain with fbd