An alloy has a yield strength of 41 ksi, a tensile strength of 57 ksi, and an elastic modulus of 16 * 106psi. A cylindrical specimen of this alloy 0.5 in. in diameter and 10 in. long is stressed in tension and found to elongate 0.3 in.On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If so, calculatethe load. If not, explain why.

Q: In the figure below, a stainless steel wire is supporting a weight, W. The Yield Strength and…

A:

Q: Which of the following is the best representation of the samples' (A and B) axial strains when…

A:

Q: 400 200 Strain 0.05 0.10 0.15 0.20 From your graph, plotting the yield stress against 1/vd, you…

A:

Q: Answer fast

A: Solution:a) Maximum Stress CalculationFormula:Maximum Stress = Fplastic  / A 3. Calculation:Maximum…

Q: The graphs in figure 5 show how tensile stress varies with tensile strain for two metallic wires…

A: Breaking stress :  It is the maximum stress at which a material can take before it fails. For copper…

Q: In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in…

A: A tensile test is performed on an aluminum specimen, whose length is 2 inches and diameter is 0.5…

Q: An aluminum tensile test specimen has a diameter, do = 25 mm and a gauge length of Lo = 250 mm. If a…

A: Given : do = 25 mm Lo = 250 mm  Force = 175 kN  Elongation of Gauge length = 1.25 mm  This is a…

Q: Given that a steel cyInder of dimenslons 12.0 mm in dlameter and 70 mm bng is subjected to tensicn.…

A: a) According to Hook's law within the elastic limit, stress is directly proportional to strain.…

Q: 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. Stress, psi

A: The given stress-strain graph of aluminum alloy is-

Q: Consider a metal bar 12.5 mm in diameter and 50 mm in length that is tested under uniaxial tension.…

A:

Q: The stress–strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length…

A:

Q: Plot the stress-strain diagram and determine the following mechanical properties: (a) proportional…

A: Given:- Initial diameter of test specimen, D = 0.505 in Length of specimen, L = 2 in Load (lb)…

Q: A specimen of aluminum having a rectangular cross section 10.4 mm × 12.6 mm (0.4094 in. × 0.4961…

A: So, stress can be defined as ; σ = PA P = Tension pull = 35900 A = 10.4 * 12.6 = 131.04 mm2 σ =…

Q: A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile…

A: Answer Based on the given data, we can calculate the minimum Elastic Modulus required for possible…

Q: Problem :6 Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

A:

Q: A piece of steel is said to have Young’s modulus of 29 × 106 psi. Based upon a yield strength of…

A: I

Q: A steel bar of 500 mm length is under tensile stress of 100 N/mm?. If the modulus of elasticity is 2…

A: Given data : Length (L)=500 mmTensile stress (σ)=100 N/mm2Modulus of elasticity (E)=2×1011  N/mm2

Q: 9 A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic…

A:

Q: To stretch a 200 mm long tensile test specimen (a) of steel elastically by 0.08 mm. How many loads…

A:

Q: A sample of aluminum is stretched by a 6 kip load. If the aluminum piece is 32 inches long, 2 in^2…

A:

Q: 90 alloy component as shown in following figure that is subjected to a stress of 200 MPa (29,000…

A: Given data stress= 200 MPa rupture lifetime be 509 h

Q: A circular rod of diameter 30 mm and length 200 mm is subjected to a tensile force. The extension in…

A: Given data:-Diameter of the rod = D= 30mmLength= L= 200mmChange in length, ∆L= 0.09Change in…

Q: The following idealized data was obtained from tensile testing of steel. It is required to determine…

A: The stress- stress curve for the given values of stress and strain is as under:-

Q: A sample of aluminum is stretched by a 6 kip load. If the aluminum piece is 30 inches long, 2 in^2…

A: Stretch load (P) = 6kipLength of piece (L) = 30in. Cross sectional area (A) = 2 in.2 Determine the…

Q: The flange of an S275 beam is 53.3 mm thick. What is the yield strength of the beam in N/mm2?…

A: Given, S275 Beam The thickness of flange=53.3 mm

Q: Problem 3: Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

A:

Q: 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. Stress, psi

A: To calculate maximum working stress, we will have to calculate yield stress. The maximum yield…

Q: Consider a square aluminum element of 3in. Dimensions as shown in figure below. If a force is…

A: Poisson's ratio (μ) = 0.33  Deformation along y-axis (δLy) = 0.02 in.  Determine the strain in the X…

Q: In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in…

A:

Q: 1. A cylindrical steel specimen, with an initial diameter of 7mm, has elongated by 40% at the point…

A: Given,  Di = 7 mm  EL = 40% P = 35 kN

Q: 1. The following data were obtained during a tension test of an aluminum alloy. The initial diameter…

A:

Q: A specimen is originally 1ft long, has a diameter of 0.5in, and is subjected to a force of 5001b.…

A: