An airflow at Mach 0.6 passes through a channel with a cross-sectional area of 50 cm?. The static pressure in the airstream is 50 kPa; the static temperature is 298 K. (a) Calculate the mass-flow rate through the channel. (b) What percent of reduction in area would be necessary to increase the flow Mach number to 0.8? to 1.0? (c) What would happen if the area were reduced more than necessary to reach Mach 1?

An airflow at Mach 0.6 passes through a channel with a cross-sectional area of 50 cm?. The static pressure in the airstream is 50 kPa; the static temperature is 298 K. (a) Calculate the mass-flow rate through the channel. (b) What percent of reduction in area would be necessary to increase the flow Mach number to 0.8? to 1.0? (c) What would happen if the area were reduced more than necessary to reach Mach 1?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer and show working out please and label each part
Water is the working fluid in a Rankine cycle. Steam exits the steam generator at 1500 lbf/in.? and 1100°F. Due to heat transfer and frictional effects in the line connecting the steam generator and turbine, the pressure and temperature at the turbine inlet are reduced to 1400 Ibf/in.? and 1000°F, respectively. Both the turbine and pump have isentropic efficiencies of 85%. Pressure at the condenser inlet is 2 Ibf/ in.?, but due to frictional effects the condensate exits the condenser at a pressure of 1.5 lbf/in.? and a temperature of 110°F. The condensate is pumped to 1600 lbf/in.² before entering the steam generator. The net power output of the cycle is 5.5 x 10S Btu/h. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. Determine for the cycle: (a) the mass flow rate of steam, in Ib/h. (b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator. (c) the percent…
Please make the charts for the questions. Please refer to Successful Project Management (7th Edition). Attached is the example Thank you.
71.7 is being marked wrong in McGraw Hill homework. I thought I had done it right with putting 86.03 but that is wrong also. I'm not trying to just find the answer, trying to find how to do this. Could there be a different number than 71.7? Where does the μk=0.20 come into the equation?
Please give a steps by steps explanation of each question answer please. Thanks you so much
Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…
Can someone help me to solve the following problem showing all work thank you!
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A
In the last few steps, where did 0.4 come from?
Help!!! Please answer part b correctly like part A. Please!!!!