According to IS 456-2000, which one of the following statements about the depth of neutral axis x bal for a balanced reinforced concrete section is correct? (a) xubal depends on the grade of concrete only (b) Xu.bal depends on the grade of steel only (c) Xu.bal depends on both the grade of concrete and grade of steel (d) X, `u,bal does not depend on the grade of concrete and grade of steel

According to IS 456-2000, which one of the following statements about the depth of neutral axis x bal for a balanced reinforced concrete section is correct? (a) xubal depends on the grade of concrete only (b) Xu.bal depends on the grade of steel only (c) Xu.bal depends on both the grade of concrete and grade of steel (d) X, `u,bal does not depend on the grade of concrete and grade of steel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 8: A-C fc=4500 psi 2 in T Grade 60 #6 bars- #4 stirrups 1.5 in. clear cover 3/4 in. max. aggregate Normal weight concrete 20 in Grade 60 #10 bars -10 in If the tension steel is well past yield and the compression steel has no strain at ultimate, where is the neutral axis measured from the top of the beam? O 1.5 in. 2.0 in. O Not enough information given O 3.83 in.
A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If fc= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
id last 3 digit 555
Referenced concrete When designing the same bim Why is the load in the case of moment greater than the load in the case of shear?
B. If f'c 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in Ib/ft? 250 mm 80 mm 130 mm 80 min 80 mm
Given A rectangular beam 250 mm wide and effective depth 500 mm has 4 bars of 22 mm diameter. Find the position of the neutral axis, the lever arm, the forces of compression and tension and the actual moment of resistance, if concrete is M20 mix and steel is Fe 415 grade. As per IS 456-2000, to what value it is to be limited?
Please give me the correct solution of this problem in principle of reinforced/prestressed concrete
Find depth of neutral axis from top fiber?
Question..
Answer Options Correct Q.No Question/Statement Answer А B D The effective length which exceeds 3 times the Reinforced Plain Slender 1 least lateral dimensions it is called as concrete Shear wall concrete column column column 2 Fast setting cement is ОРС53 ОРСЗ3 OPC43 ОРС23 The slab is designed as two way if the ratio of long span to short span is 2 22 Normal size of the coarse aggregate required 4 for building construction is 40 mm 30 mm 10 mm 20 mm All answers The aim of the designer is to design a structure which satisfy_ Safety Economy Aesthetics are correct For dam spillway construction the design engineer should select _grade of M50 M40 M70 М20 concrete. Floor fill comes under types of Imposed Load Environmental 7 Dead load Live load load. load
Given Data: Concrete dimensions Area of steel 625 560 f = 30 MPa ЗHD25 f, = 420 MPa A, = 2457 mm² 65 %3D b = 250 Required: What is the maximum uniformly distributed live load it can support in addition to dead load?