B. If f'c= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in Ib/ft? 250 mm 80 mm 130 mm 80 mn 80 mm

B. If f'c= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in Ib/ft? 250 mm 80 mm 130 mm 80 mn 80 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The design engineer specifies a concrete strength of 31.0 MPa. Determine the required average…

A: Take the standard case s=5. The formula to calculate the average compressive strength is given by,…

Q: Problem 1: A singly reinforced rectangular beam has a dimension b = 310mm and d = 410 mm. Factored…

A: The maximum depth of the neutral axis from the extreme compression fiber, xu,max =…

Q: What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if…

Q: Problem 8: A-C fc=4500 psi 2 in Grade 60 #6 bars - # 4 stirrups 1.5 in. clear cover 3/4 in. max.…

A: Given data: f'c=4500psi=31Mpafy=Grade 60=415Mpaeffective depth=d=20in=508mmMaximum depth ofneutral…

Q: The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads…

A: In the question calculation of load on the beam is permissible until and unless there will no…

Q: Determine the development length required in bar diameter for the epoxy-coated bottom bars of the…

A: The values given in the question are as follows: Steel reinforcement = 4-25 mmϕ Diameter of main…

Q: PLEASE WRITE THE COMPLETE SOLUTION NEATLY: A rectangular beam has b = 250 mm and an effective depth…

A: b = 250 mm d = 490 mm fc' = 20.7 MPa fy = 420 MPa As = 3-20mm diameter bar Calculate ultimate…

Q: A short plain concrete column with dimensions of 300 mm * 300 mm *900 mm is to be constructed. If…

A: Solution Given Data Dimension=300 mm*300 mm*900 mm Compressive strength = 34.5 MPa FOS= 1.2

Q: A short plain concrete column with dimensions of 300 mm X300 mm X 900 mm is to be constructed. If…

A: Given data in question Dimensions of short column Stress Factor of safety To find out Maximum load…

Q: The working load capacity of a column of size 300 mm x 600 mm with minimum percentage of steel is…

Q: An RCC beam having 200 mm wide and 400 mm effective depth is reinforced with Fe415 grade steel of…

Q: Help

A: Given: steel in tension zone: n = 6 bars dia. = 40 mm Beam section: b = 300 mm h = 585 mm L = 8000 m…

Q: Determine the flexural capacity of the following section using equations, the concrete is 40MPA, the…

A: Given:- concrete=40MPa steel=400MPa aggregate size=19mm To find:- flexural capacity

Q: Reinforced Concrete Design-1 Follow ACI Code (American Concrete Institute) Last two…

A: Reference : ACI Code Amount of area of steel required will be ; As As = Mu0.87 fy Z Mu = Ultimate…

Q: Determine the development length required in bar diameter for the epoxy-coated bottom bars of the…

A: Solution: Given: Bar diameter = 25 mm f'c = 21 MPa, fy = 420 MPa. cover = 80 mm Tie bars = 10 mm @…

Q: 8.2 See the following graph of the column axial load versus deformation response. Identify which…

A: Given data- The graph of the column axial load versus deformation is given as shown below- To Find-…

Q: Assuming the concrete is uncracked, compute the bending stresses in the extreme fibers of the beam…

A: Given

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 410 mm and an over-all…

A: Torsion in beams is caused by the action of shear loads whose application sites do not correspond…

Q: A. Compute the bending stress in the extreme compression fiber of the beam in the figure for a…

A: Given data:- Bending moment,M=30 KN.m=30×106 N.mm Characteristics compressive strength of…

Q: Situation: A beam has a width of 300 mm and total depth of 600 mm strength f'c-36 MPa. Steel yield…

Q: A concrete cylinder (6 x 12 in.), cured according to ASTM C 511 (100% RH and 23 °C) and tested at an…

A: We know, Stress = Load / Area Load at which the cylinder fail = 98342 lb Cross sectional area of…

Q: Problem 2: Determine the rebar size in the following beam. The beam span is 22 ft and it is…

Q: Q3- Three concrete beams were selected for flexural strength test. Results from tests are shown in…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: A rectangular beam of size 250 mm x 400 mm is reinforced with 4-20 mm bars of Fe415 grade. Effective…

Q: Problem 5: A beam is 250 mm in width, 500 mm in total height and 3.5 meters in length. This beam was…

A: Given data width of beam= 250mm Height = 500mm Length= 3500 mm compressive strength= 32MPa we have…

Q: A 300 mm wide reinforced concrete beam has an effective depth of 450 mm. It is reinforced in the…

Q: What is the cracking moment of a H=400mm by W=300mm beam if the specified compression strength of…

A: Height of beam = H = 400mm or .4m Width of beam = W = 300mm or .3m The compression strength of the…

Q: A 150mm thick concrete slab, with a span of m, which is continuous on one end, is reinforced with…

A: Given data: Thickness of slab=150 mm Span of the beam=3m Reinforcement =15 M bars Spacing between…

Q: Consider the following data: 1. 3-10 mm 0 bars are in bundle and are in compression. 2. Steel used…

A: Given data,

Q: Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The…

Q: The 20mmØ bottom bars in the figure are epoxy coated. Assuming normal weight concrete, fy= 420 MPa,…

Q: The properties of the reinforced concrete beam are b = 306 mm, d = 467 mm, Ast = 1007 mm2, and Est /…

Q: FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Calculate the uniform load (in addition to the beam…

A: Given, Span of the beam= 28 ft fc'=4000 psi fr=7.5fc'=7.54000=474.34 psi RCC weight=150 lb/ft3

Q: Determine the design strength of the beam. Use F'c= 28 MPa, Fy = 415 MPa, b = 250 mm, d' = 60 mm, d…

Q: In the extreme fiber of a concrete beam, the value of compression is 5.80 MPa. The neutral axis of…

A: Given: Compressive stress = 5.80 MPa Depth of neutral axis, y = 58 mm Compressive strength of…

Q: Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions…

A: Solution-The given values are ,f'c=21MPafy=420MPaTo DetermineThe tensile steel ratio

Q: Q-2: Estimate short-term and long-term deflections for simply supported beam shown in Figure below,…

A: Modulus of elasticity(E)=26 kN/mm2,Yield strength(fy)=460 kN/mm2,Dead load(DL)=10 kN/m,Live…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

B. If f'c 3200 psi and normal weight of concrete is used, does cracking occurs? What
is the maximum uniformly distributed load the beam can carry if it is used as a
simple beam with a 26 ft span without exceeding the modulus of rupture of the
concrete, in Ib/ft?
250 mm
80 mm
130 mm
80 min
80 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q- The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm tested as per the split tensile strength test guidelines of IS 5816:1999 is 157 kN. The split tensile strength (in MPa, round off to one decimal place) of the specimen is?
Do it fast
Bottom of the question answers given(not the grade)
1. What component of concrete that has affect its strength largely? Explain. 2. If you have to choose, an expensive high quality concrete or a less expensive with low quality concrete? Explain. 3. To reduce corrosion on steel reinforcement, what you have to consider in the design? 4. A 300mm X 500mm concrete beam with a 25mm diameter reinforcing bar spaced at 50mm o.c will be constructed using a non-air entrained concrete. The design compressive strength at 28 days is 30 MPa. Design a concrete mix for the beam. The properties of the aggregates and cement to be used are given in the table below. Use a trial batch of 0.15 m3. Specific Gravity Absorption Moisture content Coarse aggregate 2.75 (SSD) 1.2% Fine aggregate Cement 2.56 (SSD) 3.15 2.5% 2.5% 4.5% Unit weight (dry 1750 kg/m3 rodded) FM 2.45
Design strength for M25 concrete in direct compression, bending compression and flexural tension are, respectively A 10 MPa, 11.15 MPa and 3.5 MPa B 25 MPa, 11.15 MPa and 3 MPa с 10 MPa, 12.5 MPa and 3.5 MPa D 25 MPa, 11.15 MPa and 2.57 MPa
The flexural tensile strength of M25 grade of concrete, in N/mm², as per IS:456-2000 is A 0.5 B 5 C 2.25 D 3.5
Plz, solve this problem in all its parts. Reinforced Concrete Design-1 Follow ACI Code (American Concrete Institute) Last two digits of Registraion Number: 95 A simply supported beam having span length of 24′ and cross-section of 15" × 21"is subjected to an ultimate load of ?? k/ft. Taking ?c = 3??? and ?y = 60???, a) Calculate the amount of reinforcement required for a given beam section to fail under balanced condition.b) Determine the magnitude of strain developed in the tension steel at the ultimate stage if the magnitude of ?? = (?/10) k/ft. Where ? = Last two digits of Registration Number
Please give me right solution. Urgent A formed in place beam has the followonf dimensions: 3ft x 120ft x 6in
Arectangular concrete hollow section simply supported beam shown below have the following dimensions: b= 10-inch, w = 2 inches and h = 18 inches and spans 14 ft. The section should carry its own weight and imposed a dead load of 150 Ib/ft and a live load of 50 lb/ft. If the young's modulus is 10.2 x 10° psi and the density of concrete is 150 Ib/ft³, calculate the: 1. Permissible bending stress if the concrete strain is 0.003 2. The moment resistance of the beam 3. The maximum bending moment b w
The permissible bending compressive strength for M 25 grade of concrete is 8.5 N/mm². Its short-term and long-term modular ratios are, nearly
Read the question carefully and give me all right solutions. Note: kindly answer all(a, b, c, d) otherwise leave it
A simply supported beam shown in figure 1, carries an uniform service (unfactored) superimposed deadload of 1.4 kips/ft. plus its own weight and a liveload of 1.5 kips/ft. The concrete strength is 3,500 psi, and the yield strength of the reinforcement is 60,000psi. The concrete is normal- weight concrete. Use the load and strength reduction factors from ACI Code. Compute the design strength or capacity at the midspan of the beam and check if it is safe or adequate to resist the factored service moment. a). 220 kips-ft., safe Figare li wds 14 kipplr.; We= 1,5 kips /. し,vbv b). 336 kips-ft., safe 215" c). 128 kips-ft., inadequate 3 ho. 9 ars d). 255 kips.ft., adequate Solution: