(a). Determine the form factors for the timbAlso, compare their load carrying capacity if the beams are made of timber of group B and thebeam is being used for inside location.(i)Rectangular beam : 21 cmx 42 cm(ii)Built-up I beam 7 x 42 cm web and 7x42 cm flanges.(iii)circular beam of area 882 cm2(iv)Square beam of area 882 cm, with load acting along a diagonal.

Answered: Image /qna-images/answer/3c19b031-25a7-4638-b1a9-356749377a7b.jpg

a). Determine the form factors for Also, compare their load carrying capacity if the beams are made of timber of group B and the beam is being used for inside location. Rectangular beam : 21 cm x 42 cm (ii) Built-up I beam : 7 x 42 cm web and 7x42 cm flanges. (ii) circular beam of area 882 cm? (iv) Square beam of area 882 cm, with load acting along a diagonal.

a). Determine the form factors for Also, compare their load carrying capacity if the beams are made of timber of group B and the beam is being used for inside location. Rectangular beam : 21 cm x 42 cm (ii) Built-up I beam : 7 x 42 cm web and 7x42 cm flanges. (ii) circular beam of area 882 cm? (iv) Square beam of area 882 cm, with load acting along a diagonal.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

View Policies Current Attempt in Progress The wood beam supports loads of w = 460 lb/ft and P = 120O Ib on span lengths of LAB = 9.0 ft, LBC = 4.5 ft, and LcD= 4.5 ft. The beam cross section has dimensions of b, = 1.4 in., d, = 4.2 in., b2 = 4.5 in., and d, = 11.60 in. Determine the magnitude and location of: (a) the maximum horizontal shear stress in the beam. (b) the maximum tensile bending stress in the beam. P W di d2 B LAB LBC LCD by b2 Answer: (а) Тmax psi (b) Omax = psi Save for Later Attempts: 0 of 1 used Submit Answer
Determine the theoretical steel areas required for tension of a rectangular section with b = 350 mm, d = 600 mm under a factored moment of 1,500 kN-m. If compression steel is required, assume it will be placed 70 mm from the compression fiber of concrete. Use fc’ = 28 Mpa and fy = 420 Mpa.Usingabar size of your choice, determine the number of bars required and design the bar lay-out.(For the purpose of laying-out, use 10mm diameter bars for stirrups.)
6. Timber floor: The cross-section of the beam is 8x22cm (bxh), axial spacings 0,60 m. Timber class C24. Span of beam measured between walls is 5,20 m. Self weight of floor is 1,50 kN/m. Imposed load of floor is 2,00 kN/m2. Design required reinforcement. Only consider ULS. Please make appropriate drawing.
A composite beam is fabricated by bolting two 3.6-in.-wide by 13-in.-deep timber planks to the sides of a 0.5-in. by 13-in. steel plate. The moduli of elasticity of the timber and the steel are 1700 ksi and 29000 ksi, respectively. The simply supported beam spans a distance of 25 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD = 7 ft, LBc = 11 ft, b = 3.6 in., d = 13 in. and t = 0.5 in. (a) Determine the maximum bending stresses o,,o, produced in the timber planks and the steel plate if P = 3.7 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1010 psi and 26800 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: LAB (a) o, = (b) P = i i B LBC b F لالها b Cross section C kips. d ksi, o, = LCD D ksi.
A 4 × 4 carries an axial compressive force caused by dead, live, and roof live loads. Lumber is No. 1 DF-L. CM = 1.0, Ct = 1.0, and Ci = 1.0. Find: The allowable column load for each load combination if the unbraced length of the member is a. 3 ft b. 6 ft c. 9 ft d. 12 ft
PROBLEM 1: A reinforced concrete beam has a simple span of 8m. It carries a concentrated factored load, Pu=200KN (40% DLcand 60%LL), at midspan. The beam is reinforced with 3D25mm. It has a width of 300mm and andepth of 400mm and 12mm stirrups. Take fc' to be 24MPA and fy=420MPA and fyt=280MPA. Use simplified calculation of Vc 1. What is the ultimate shear capacity of concrete at a section 2m from the support, KN? 2. What should be the shear capacity of web reinforcement at the section 2m from the support, KN? 3. What is the maximum spacing of web reinforcement allowed by the code (NSCP) at the section 2m from the support if the diameter of stirrups is 12mm, mm? 4. What is the required spacing of web reinforcement at the section 2m from the support if the diameter of stirrups is 12mm, mm?
2. Roof joists are spaced at 2m and span 6m between supporting girders, and joist depth of 600mm. The allowable deflection limits for OWSJ are L/360 under snow load. The OWSJS are subjected to a dead load of 2.96kPa which includes the estimate joist weight of 0.15kPa, an occupancy load of 2.4kPa, and the following: SULS 1.99kPa SSLS = 1.25kPa Select a suitable OWSJ which satisfies the limit states design.
A composite beam is constructed of a Southern pine [E = 10 GPa] timber, 200 mm wide by 360 mm deep, that is reinforced on its lower surface by a steel [E = 337 GPa] plate that is 150 mm wide by 12 mm thick. Find the distance to the centroid of the transformed section from the bottom surface of the beam. 200 mm 360 mm -PL 150 × 12 127.7 mm 100.7 mm 147.2 mm O 75.6 mm O 106.9 mm
A laminated wood beam consists of eight 2.25 in. × 5.00-in. planks glued together to form a section b = 5.00 in. wide by d = 18 in. deep, as shown and w = 663.2 lb/ft. If the allowable strength of the glue in shear is 105 psi, Determine:(b) the shear stress in the glue joint at H, which is located 4.5 in. above the bottom of the beam and at a distance of x = 86 in. from the left support. Assume that the beam is subjected to the load w determined in part (a). [Answer: τH = 19.34 psi]
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
please give detail on how to get all value and diagram
I am trying to figure out which equations were used to solve this problem.