A composite beam is constructed of a Southern pine [E = 10 GPa] timber, 200 mm wide by 360 mm deep, that is reinforced on its lower surface by a steel [E = 337 GPa] plate that is 150 mm wide by 12 mm thick. Find the distance to the centroid of the transformed section from the bottom surface of the beam.

A composite beam is constructed of a Southern pine [E = 10 GPa] timber, 200 mm wide by 360 mm deep, that is reinforced on its lower surface by a steel [E = 337 GPa] plate that is 150 mm wide by 12 mm thick. Find the distance to the centroid of the transformed section from the bottom surface of the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the reference bending stress for Spruce-Pine-Fir No. 2 dimension lumber?Fb=_______ psi
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
A singly reinforced rectangular beam has a dimension b 310 mm and d = 410 mm Factored moment is equal to 100 kN-m, Concrete compressive strength is 24 MPa, Steel yield strength is 275 MPa and the reduction factor is 0.9. Determine the required steel area in mm?
A laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150 mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 KPA, and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the beam on a 45 m simple span.
The middle of the 5.6 m simple beam has a dimension of 350 mm by 600 mm. On that location, the beam is reinforced with 3-020mm on the top and 7-020 mm at the bottom. The concrete cover to be used is 40 mm. The stirrups used is 12 mm in diameter The concrete strength of the beam is 27.6 MPa. All reinforcement used is Grade 60 (y = 420 MPa). The beam is carrying a superimposed dead concentrated load of 55 kN and an unknown superimposed live load both at the midspan. The unit weight of concrete used is 23.6 kN per cubic meter Determine the unknown concentrated live load that the beam can sustain.
A timber beam 150 mm wide and 200 mm deep is to be reinforced by bolting on two flitched each 150 mm x 12.5 mm in section. Find the moment of resistance when the flitched are attached symmetrically at the top and bottom. Allowable stress in timber is 6 N/mm². (Es= 20 Ew)
A laminated wood beam consists of eight 2.25 in. × 5.00-in. planks glued together to form a section b = 5.00 in. wide by d = 18 in. deep, as shown and w = 663.2 lb/ft. If the allowable strength of the glue in shear is 105 psi, Determine:(b) the shear stress in the glue joint at H, which is located 4.5 in. above the bottom of the beam and at a distance of x = 86 in. from the left support. Assume that the beam is subjected to the load w determined in part (a). [Answer: τH = 19.34 psi]
(a) Draw the shear and bending-moment diagrams for the beam and loading shown below. 48 kips 48 kips 48 kips B A E -6 ft- 2 ft' 2 ft 2 ft (b)If the cross-section of the beam is as shown below, determine the maximum tensile and compressive stresses. 8 in. 1 in. 1 in.- 6 in. 1 in. 4 in.
Beam, flexural.
.