2. Determine if the composite beam pictured below is adequate for this application (this includes bending, shear, deflection and shear stud limit states). The dead load for this beam is 10 psf plus the weight of the deck, which is made from normal weight concrete. W24x94- 8' 0.c. typical I[ 11 5" 5" Normal weight slab fc=4000 psi Span length = 30' Service Live Load = 100 psf 3/4" Diameter Shear Connectors Fu=60 ksi (shear connectors)

2. Determine if the composite beam pictured below is adequate for this application (this includes bending, shear, deflection and shear stud limit states). The dead load for this beam is 10 psf plus the weight of the deck, which is made from normal weight concrete. W24x94- 8' 0.c. typical I[ 11 5" 5" Normal weight slab fc=4000 psi Span length = 30' Service Live Load = 100 psf 3/4" Diameter Shear Connectors Fu=60 ksi (shear connectors)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: DETERMINE THE MOMENT OF INERTIA USING THE GIVEN X-AXIS OF THE SHADED COMPOSITE AREA AND…

Q: Determine the numbers of rebars required for a RC beam (h=400mm, b=700mm) carrying a factored moment…

A: Given b= 700 mm h= 400 mm Cc = 40 mm, db = 20 mm , ds = 10 mm Characteristic strength of…

Q: 3. A simply supported beam (Span / -25 ft) has a section as shown below with normal-weight concrete…

Q: A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12…

A: Given data Concrete weight (wt) = 150 pcf Find maximum bending moment due to self weight of beam.…

Q: Determine the LRFD moment capacity (φbMn) of a composite section that is comprised of a W30x99 with…

A: given data, W30x99 beam span is 30-ftspacing of the beams is 8-ftf’c = 4 ksislab thickness=5…

Q: 1) It is not necessary to install reinforcing steel in concrete under compression? Tor F 2) Nominal…

A: Brief concept introduction- Reinforcing steel- These are the steel bars that are used with the…

Q: Problem 2: Determine the rebar size in the following beam. The beam span is 22 ft and it is…

Q: In prestressed concrete beams, draped or harped tendons are usually used instead of straight…

A: The prestressed concrete is defined as “the process of inducing the internal stresses in the…

Q: Q2: Design a typical interior flat slab panel 18x15ft as shown in the figure rested on squared…

A: Solution: Given: slab panel = 18 x 15 ft squared column = 21 x 21 in slab thickness = 14 in DL = 32…

Q: A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when…

A: Given data: Section W360 x 72 @ 1000mm fck = 25 MPa Density of concrete = 24kN/m3 Slab thickness =…

Q: Given: A fully composite slab is connected to a W24x68 made with the manufacturer preferred…

A: Solution; Given that; 3.5 m simply supported on 20 mm thick wall to support a live load of 4 KN/m2.…

Q: Check the following reinforced concrete beams for bending. The beams are on a simple span of 26.5ft.…

A: Loading : 3.20 kip/ft live and 1.80 kip/ft dead excluding beam weight. L = Simple span length =…

Q: A simply supported beam (Span = 25 ) has a seetion as shown below with normal-weichs concrete…

Q: A rectangular beam has the dimensions b=12in., h=26in., and d=24 in. and is reinforced with three…

Q: A simply supported beam (Span = 25 ) has a seetion as shown below with normal-weichs concrete…

Concept explainers

Composite Construction

Composite construction is the construction of structures in which two or more materials are used. Regarding structural engineering, composite construction is a construction where two materials are bound together in a technical manner such that both the materials act as a single unit to carry and transfer the load. The motives of composite construction are to increase the structural strength, make structures more aesthetic, and provide a sustainable environment.

Question

2. Determine if the composite beam pictured below is adequate for this application
(this includes bending, shear, deflection and shear stud limit states). The dead
load for this beam is 10 psf plus the weight of the deck, which is made from
normal weight concrete.
I
5"
5" Normal weight slab
fc=4000 psi
W24x94
Span length = 30'
Service Live Load = 100 psf
3/4" Diameter Shear Connectors
8' o.c. typical
Fu=60 ksi (shear connectors)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

VIEW

Step 2: Capacity of Beam

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fully composite section that is comprised of an A992 W16x31 with a 5-inch, (f'c= 4 ksi) slab on top of it. The beam span is 30' and the spacing of the beams is 5-foot. All the shear studs to make the composite beam were completely forgotten to be installed by the contractor. Assume that the friction between the slab and the steel beam is enough to provide continuous lateral support to the compression flange of the steel beam but provides no composite action between the concrete and the steel. What is the LRFD moment capacity (4bMn) of this badly built attempt at a 'composite' beam, Hint; The flexural strength of the unreinforced concrete slab is 7.5*(f'c)^0.5 Also, the fundamental flexural equation is MC/I. Show all work.
Problem 2. A composite section having an effective width of flange of 2100 mm and a slab thickness of 150mm as shown in the figure. The steel beam is WS30 x 101 of A36 steel with Fy =250 MPa. Concrete fc'=20.7 MPa. Modular ratio, n=9. Assume full shoring and full composite action. A 12900 mm2 d= 537 mm Properties of W 530 x 101 W= 101.4 kg/m k=617 x 10 mm 2100mm 150mm W530x10/ a. Determine the moment of inertia at the neutral axis. b. Determine the resisting moment for the cross section shown. c. Determine the uniformly distributed load which excludes the weight of the steel beam and concrete slab that the beam could support if ithas a simplespan of 6m.
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
(e) Regardless of the load duration (i.e., standard, permanent, or short term), the wet service condition causes almost the same reduction in the compressive strength for glulam sections. (
A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculate
A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when cast is to be 100mm thick concrete (25MPA). The shear studs to be used have an ultimate stress capacity of 415MPA and will have a diameter of 16mm. Assuming 100% connection and that the system is shored during casting determine the ultimate moment of the composite W360.
Size an A992 W shape given the following information; -Beam span is 20 ft and simply supported -Floor beams are 6 ft on center -Cb=1.0 (don't forget self-weight) -The beam will support a plywood deck (3 PSF) oriented perpendicular to the beam -The average concrete (normal weight) thickness is 4.5 in Assumption - 50% ponding factor during the concrete placement and treat the concrete as a live load - 10 Psf for the concrete workers live load - Plywood framework is used instead of steel decking - the beam has no support of the compression flange over its length