A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when cast is to be 100mm thick concrete (25MPa). The shear studs to be used have an ultimate stress capacity of 415MPa and will have a diameter of 16mm. Assuming 100% connection and that the system is shored during casting determine the ultimate moment of the composite W360.

A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when cast is to be 100mm thick concrete (25MPa). The shear studs to be used have an ultimate stress capacity of 415MPa and will have a diameter of 16mm. Assuming 100% connection and that the system is shored during casting determine the ultimate moment of the composite W360.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer Options Correct Q.No Question/Statement Answer A Select the grade of concrete required for 1 М5 M50 M15 М80 airport runways. The load which has fixed size and location is 2 called as Environmental All answers Dead load Live load Load are wrong Top surface of the tensile Bottom The clear cover of the RCC beam is taken as Centre of surface of the Bottom of the gravity of the tensile steel vertical distance from the base of the beam to steel tensile steel beam the reinforcement reinforcement 4 Stocky column generally fails by_ Compression Tension Buckling Deflection In a one way slab the main reinforcement is provided along All answers Both long and short span Long span Short span are wrong All answers Flat slab is placed above Drop panels Column Column head are correct The maximum percentage of reinforcement in 7 RCC short column, based on practical 0.8% 4% 6% 2% difficulties is For reinforced concrete wall D4B When to columns are far, select the type of foundation Trapezoidal…
RCDA reinforced concrete T- beam, section in Figure 2 (a), is subjected to an ultimate uniformload and concentrated loads as shown in the Figure 2(b). The beam is reinforced with 6-28 mm diameter tension bars at the point of maximum positive moment (at midspan -bars at the bottom), and 3-28 mm diameter tension bars at the point of maximum negativemoment (at the supports - bars at the top) .. The design properties used are: f ‘c = 21MPa and fy = 414 MPa, ; flange width = 650 mm, flange thickness is = 90 mm; webthickness = 250 mm; effective depth = 410 mm.Need to answerQ. Draw the shear and moment diagrams for the given loads;
In the design of beam for the limit state of collapse in flexure as per IS 456 : 2000, let the maximum strain in concrete be limited to 0.0030 (in place of 0.0035) for this situation consider a rectangular beam section of width 300 mm, effective depth as 400 mm, area of tension steel used is 900 mm2. Material used is M20 concrete mix Fe415 grade steel (a) Limiting depth of neutral axis (b) Actual depth of neutral axis
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
S Maximum strain in extreme fibre of concrete and in tension steel of Fe 415 grade (E = 2 x 105 N/mm²) in a balance section in limit state of flexure are respectively (a) 0.0035 and 0.0031 (b) 0.0035 and 0.0038 (c) 0.002 and 0.0042 (d) 0.002 and 0.0038
A laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150 mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 KPA, and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the beam on a 45 m simple span.
A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculate
1 Situation 19. A composite beam shown is subjected to a bending moment of 500 kN-m. Determine the maximum flexural stress; 300 VIEW INNOVATIONS 200 200 100 55. Experienced by the steel 56. Experienced by the aluminum A. 0.03 B. 25.24 57. Experienced by the brass A. 25.24 B. 37.86 REVIEW I EW INNOVATIONS Steel, E=200 GPa Aluminum, E=70 GPa Brass, E-105 GPa wwwww C. 48.2 D. 72.11 C. 16.8 C. 16.8 D. 11.21 VIEW INNOVATIONS REVIEW INNOVATIONS REVIEW IS
Required information A composite beam is made by attaching the timber and steel portions shown with bolts of 12-mm diameter spaced longitudinally every 200 mm. The modulus of elasticity is 10 GPa for the wood and 200 GPa for the steel. The vertical shear is 4.4 kN. 12 mm 250 mm 12 mm 150 mm- Determine the average shearing stress in the bolts. (Round the final answers to two decimal places.) The average shearing stress in the bolts is MPa.
Beam, flexural.
Size an A992 W shape given the following information; -Beam span is 20 ft and simply supported -Floor beams are 6 ft on center -Cb=1.0 (don't forget self-weight) -The beam will support a plywood deck (3 PSF) oriented perpendicular to the beam -The average concrete (normal weight) thickness is 4.5 in Assumption - 50% ponding factor during the concrete placement and treat the concrete as a live load - 10 Psf for the concrete workers live load - Plywood framework is used instead of steel decking - the beam has no support of the compression flange over its length