A Y-connected balanced three-phase generator with an impedance of 0.4 +j3 ohm per phase is connected to a Y-connected balanced load with an impedance of 24 +j19 ohm per phase. The line joining the Generator and the load has an impedance of 0.6 +j 0.7 ohm per phase. Assuming a positive sequence for the source voltages and that van = 120/30° V., Determine (a) all the line voltages, (b) all the line currents:.

A Y-connected balanced three-phase generator with an impedance of 0.4 +j3 ohm per phase is connected to a Y-connected balanced load with an impedance of 24 +j19 ohm per phase. The line joining the Generator and the load has an impedance of 0.6 +j 0.7 ohm per phase. Assuming a positive sequence for the source voltages and that van = 120/30° V., Determine (a) all the line voltages, (b) all the line currents:.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power system class, can you please show steps so I can understand
A balanced three-phase, negative sequence, Y-connected generator is connected to a three-phase balanced Y-connected load. The generator has an impedance of 1.5-j1.25 Q/phase. The impedance of the line connecting the generator to the load is 2.5+jl1.25 0/phase. The phase "B" load voltage is 1520° kV. The impedance of each phase of the Y-connected load is 60-j80 Q/phase. Calculate phase voltages \(V_{an}\) at the generator. \(V_{an}=\) Volts
18. A 415 V, 50 Hz, 3-phase supply of phase sequence RYB is connected to a delta connected load in which branch RY consists of R, = 100. branch YB conists of R₂ = 20 2 in series with X₂ = 60 Q and branch BR consists of a capacitor C= 30 uF. Take Vy as the reference and calculate the line currents. Draw the complete phasor diagrams. (Elect. Machines, A.M.I.E. Sec. B. 1989) 14.54, 1, 10.66 2172,92, 14.46 2-471 (1 = 7.78
Three single-phase transformers are connected Star-delta to step down a line voltage of 221 kV to 35 kV to supply a load of 26 MW at a lagging power factor of 0.89. Calculate the line current in the primary side, IL p. in ampers ILp
Referring to the circuit shown in Figure 1 below, solve the following problems: - i) Calculate the total impedance, ZT. ii) Determine the total current, Ir supplied by the generator iii) Determine the value of current at load impedance, I1, I2 and I3. iv) Calculate total real power, PT and reactive power, Qr supplied by the generator. v) Draw a power triangle of this circuit vi) Calculate the power factor of this circuit.
Two three-generator are parallel at 6.6 kV and delivering 3000 kW at 0.8 pf. The impedance for machine A is 0.5+j10 ohm and for B 0.4+j12 ohm. The excitation of A is adjusted to deliver 150 A at lagging pf. Determine the induced emf of machine A.
A single phase, unity power factor load takes 90 Amps at 10 kV. Using a base voltage of 65 kV and base kilovolt amperes of 4475 kVA. Find the base current, base impedance, base power, per unit current and per unit voltage of the load.
solve it
Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of 60 Hz, this generator can be connected in both delta and star. Also consider the following 6 load impedances, which will be connected at the same time to the generator as follows: ZA, ZB and Zc are connected in star, while Zp, Zg and Zp are connected in delta. j20 j3n Za j20 ZA j30 j3n -j20 j 30 -j20 Zo -j20 ZE j30 -j2n j 3n. ZF Assume the generator is star-connected with neutral, calculate total system power, total power factor, and current in neutral.
20) Two AC generators A and B are in Parallel. Each generator has an emf of 1000V per phase and in phase, the phase impedance are ZA = 0.1+j2 ohms, ZB = 0.2+j3.2 ohms respectively. If the common load has an impedance of (2+j1) ohms per phase, solve the voltage per phase at the load
Solve A-E
Two single-phase loads are connected in parallel, where load 1 is 4.7 kVA at 0.87 lagging power factor, and load 2 is5.2 kWat0.79lagging power factor. The load combination is connected to a voltage source of220VAC,50 Hz. a) Find the total complex power