A balanced three-phase, negative sequence, Y-connected generator is connected to a three-phase balanced Y-connected load. The generator has an impedance of 1.5-j1.25 Q/phase. The impedance of the line connecting the generator to the load is 2.5+jl1.25 0/phase. The phase "B" load voltage is 1520° kV. The impedance of each phase of the Y-connected load is 60-j80 Q/phase. Calculate phase voltages \(V_{an}\) at the generator. \(V_{an}=\) Volts

A balanced three-phase, negative sequence, Y-connected generator is connected to a three-phase balanced Y-connected load. The generator has an impedance of 1.5-j1.25 Q/phase. The impedance of the line connecting the generator to the load is 2.5+jl1.25 0/phase. The phase "B" load voltage is 1520° kV. The impedance of each phase of the Y-connected load is 60-j80 Q/phase. Calculate phase voltages \(V_{an}\) at the generator. \(V_{an}=\) Volts

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
Number 17
If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
Two three-generator are parallel at 6.6 kV and delivering 3000 kW at 0.8 pf. The impedance for machine A is 0.5+j10 ohm and for B 0.4+j12 ohm. The excitation of A is adjusted to deliver 150 A at lagging pf. Determine the induced emf of machine A.
There is a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with clockwise sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”. a) Determine phase currents in the generator, lines and phase in the load
In the following power system M ilio YA T₂ L47 YA 5 ΔΥ synchronous generators G₁,G₂ and synchronous motor M all have the same per-unit impedances Xo=0.05, X₁=X₂=0.7 The three transformers T₁, T₂, T3 are identical with X=0.1pu. Finally, the three transmission lines L47, L57, L67 are identical with per-unit impedances X₁=0.2, X₁=X₂=0.1 Pre-fault all voltages are 1 pu. Then the a phase at bus 6 faults to ground (through zero impedance). What is the magnitude of the per-unit fault current? उह 4 7 L 67 L 57 Y
For the system as shown in the following figure, convert the components to same base voltage and apparent power, by choosing 100 kVA as the base kVA and 2000 V as the base voltage for the generators. Redraw the single line diagram with the new per unit values. 15 KVA 2000 V Z=j0.3 pu 25 KVA 2000 V Z=j0.15 pu G1 G2 35 KVA 2000/8000 V Z=j0.2 pu Z=30+j100 Z=60+j120 pu O pu leee 35 KVA 8000/2000 V Z=j0.3 pu 35 kVA 2000/8000 V Z=j0.25 pu G3 10 KVA 2000V Z=j0.35 pu M 30 KVA 2000 V
A three-phase alternator generating unbalanced voltages is connected to an unbalanced load through a 3-phase transmission line as shown in figure. The neutral of the alternator and the star point of the load are solidly grounded. The phase voltages of the alternator are Ea = 1020º, Eb = 102-90°, Ec = 10/120⁰ E E E The positive sequence component of the load current is (A) 1.3102-107⁰ A (B) 0.3322-120° A (C) 0.9962-120º A (D) 3.5104-81⁰ A +) + j1.002 0000 j1.002 0000 j1.0Ω vovo j1.0Ω 0000 j2.002 voor j3.002 oooo
How does a three-phase power system differ from a single-phase power system, and what are their respective applications?
Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of 60 Hz, this generator can be connected in both delta and star. Also consider the following 6 load impedances, which will be connected at the same time to the generator as follows: ZA, ZB and Zc are connected in star, while Zp, Zg and Zp are connected in delta. j20 j3n Za j20 ZA j30 j3n -j20 j 30 -j20 Zo -j20 ZE j30 -j2n j 3n. ZF Assume the generator is star-connected with neutral, calculate total system power, total power factor, and current in neutral.
5. A generating station has the following daily load cycle: Time in 0 to 6 6 to 10 10 to 12 to 16 to 20 to Hours 12 16 20 24 Load 50 60 70 60 80 50 (MW) Draw the load curve and Estimate: i. Maximum Load ii. Units generated per day iii. Average Load iv. Load Factor
Q1. For the system shown in Figure Q1, draw an impedance diagram in per unit, by choosing 100 kVA to be the base kVA and 2400 V as the base voltage for the generators. 10 KVA 2400 V G₁ Z=j0.2pu 20 KVA 2400 V Z=j0.2pu G₂ T₁ Transmission Line Z= (50+j200) 40 KVA 2400/9600 V Z=j0.1pu Fig Q1 T₂ 80 KVA 10/5 kV Z=j0.1pu M 25 KVA 4 kV