A wooden post has cross section bx b of length L with allowable compressive stress parallel to grain p(all) = = MPa. It carries a concentrated load P as a short column class 1. Find the maximum allowable load P (in Newton with 2 decimals) and the maximum allowable length L b = 106 mm p = 9.00 MPa P P P+ Top View 700mm 100mm O O Side View 100mm 200mm P

A wooden post has cross section bx b of length L with allowable compressive stress parallel to grain p(all) = = MPa. It carries a concentrated load P as a short column class 1. Find the maximum allowable load P (in Newton with 2 decimals) and the maximum allowable length L b = 106 mm p = 9.00 MPa P P P+ Top View 700mm 100mm O O Side View 100mm 200mm P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) The short steel post as shown in Figure 4 is a 152 x 152 UC37 with three compressive loads applied to the top. There is a central load of 200KN and eccentric loads of 'W kN and 100kN. The maximum allowable stress on the face AB is 185 N/mm?. (Area=D47.1cm2,Zxx=273cm) What is the value of the load 'W in kN? WkN A. 152 x 152 UC37 100mm -200KN 50mm 100KN Not to scale Figure 4
Please show your solution on a paper with FBD
Explain in detail with figures( FBD) and in hand written
A beam shown below has a T-shaped cross section. Determine the location of maximum compressive stress from left support of the beam. I = 87-49 in 4 400 16/ft 16001b 160016 I↓↓↓I LOFT #. £7 32000 lbft 2.914 in 5.886 in B -NA 34/00/6 4FT 10° 100016 -240016 1000lb dc -4000 16 ff V M
The one end of a hollow square bar whose side is 10 with 1 thickness is under a tensile stress 102500 and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σall =243000 psi for pin material.
Consider the figure 1 below: 3-25mmø bolts are used to fasten a plate to a steel beam a) Determine the average shearing stress caused in each bolt by the 30kN loads. b) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 6OMPA. 30 kN 150 300 200 P 30 kN 75 Foot
TASK 3 250 180 14 I 30 24 Weld 450 A compound girder consists of a steel joist with steel plates welded onto each flange as shown. If the ends are simply supported and the effective span is 10 m, what is the maximum UDL which can be supported by the girder? [kN/m] Allowable longitudinal stress in plates = 110 MN/m² Allowable load in shear for each weld = 60 kN/m Allowable shearing stress in web of girder = 75 MN/m² Note: 1.0 MN/m² = 1.0 N/mm² 50
2. Calculate the internal forces in the bar GF and GD in a roof truss as shownbelow. For each bar, indicate if the internal force is tensile or compressive. Usethe section method (snittmetoden). Point A has simple support and D has rollersupport.
A wide flange section has the following properties. A- 6645 mm? bị = 152.40 mm ty - 10.80 mm d- 449.58 mm tw - 7.62 mm Fy - 250 MPa Compute the plastic section modulus about the major principal axis. (x 10° mm)
CE 1
Answer 15&16