1-A simply supported beam is composed of three plates, which are fastened together using bolts that are spaced at 150mm intervals in the longitudinal direction of the beam. If the allowable shear on the bolts is 15 kN, what is the maximum allowable value of the applied load P? 24 24 Bolts spaced at 150 mm P 70 longitudinally 1.5m 50 5m dimensions in mm 100 24 Beam cros-section

1-A simply supported beam is composed of three plates, which are fastened together using bolts that are spaced at 150mm intervals in the longitudinal direction of the beam. If the allowable shear on the bolts is 15 kN, what is the maximum allowable value of the applied load P? 24 24 Bolts spaced at 150 mm P 70 longitudinally 1.5m 50 5m dimensions in mm 100 24 Beam cros-section

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.4.2P

See similar textbooks

Similar questions

Test#1 -zzen-zax AlpQLSdM75VMOVqbMa1WtS9n99RYc6PifeGUTpVBOluyMUUVYQgqqA/formResponse YouTube Replace the three forces which act on the bent bar by a force-couple system at *.the support point A 2100 lb 4' 1500 lb •A B. 30° C. 2' •E. 800 lb 3' oogle
Round off final ans only, dont round off initial values ty
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
4. A flanged bolt coupling consists of eight steel 20-mm voIs spaceu evenly around a bolt circle of300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress in the bolts is 40MP.. Det the 4 ways to increare M3 HW 3 the torque capacity to 24 KN-m a) no. d bofts ) Ss d bolti c) Dia of bolts d) Dia of belt eircle) change vn ad Make sure that orly one aspect a
10/- find the bearing stress between bolts and plate 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 125 MPa 12.5 MPа О 250 MPа no one O 8 mm 300mm 3. 4) -O--O O 5,
CH2-Hetant pa-Aote Acrobet Pro titended Ee Vien Decumem Comments Forme Tacs adanced wedew Hep 2/86 If the resultant of the loads shown passes through point B, determine the equivalent force-couple system at O. 45 kN 54 kN 1.2 m 0.9 m 0.9 m M 18 kN ahid ham
ASAP dont round off initial values, round off final ans only ty
Round off final ans only, dont round off initial values ty
Answer with solution asap
Question 3 Determine the capacity of plate as well as below connection based on Balts (4) in the below Following reactions :- 7 11 A325, $4 þ Bolts use! Use: AISC manual U Moment = 10 kip-67 2 kip (2) Shear (3) Axial 2 kip رب Ź Plate (A 36) 10 " x 10" x ≤ 11 8 HSS. их их nxuxt 4 H² 7
0: ll zain IQ docs.google.com/forms O no one 0/10 find the tensile stress in upper plate in section 1-1 5 1 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN B-bolt DIA. 10 MM 30 MPa O 33 МРа 35 MPa 37 MPa no one + ... 300 mm
9. The gusset shown is riveted to the column flange by 7-20mm diameter rivet single shear. Determine the stress in the most heavily loaded bolt. If the design shear stress is 400MPA, determine the ultimate load that the connections can carry. Using the design shear stress how much more torque can the connections carry? 140 kN 200 mm 175 mm 7- 20 mm bolts 150 mm 150 mm 150 mm