A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and in the bolts is 58 MPa, how many 14 mm-diameter steel bolts must be used on a 200 mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft? This is an exception to our two decimal rule so our answer here must be -- rounded to the NEXT whole number.

A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and in the bolts is 58 MPa, how many 14 mm-diameter steel bolts must be used on a 200 mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft? This is an exception to our two decimal rule so our answer here must be -- rounded to the NEXT whole number.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Field-flow fractionation flow fieldCould a turbulent-flow field be employed in field-flow fractionation?If so, why or why not?
A steel block of size 300 mm X 150 mm X 100 mm subjected to load of 300 kN (tension) on 150 mm X 100 mm face, 500 kN (compression) on 300 mm X 150 mm face and 100 kN (tension) on 300 mm X 100 mm face. Determine change in volume if poisons ratio is 0.25, E = 2 X 10^5 MPa
ADT construction materials? Respond.
need help...thnks..
Determine radius of mohr circle and maximum principal stress
Please solve this question step by step
5.20 Calculate the sieve analysis shown in Table P5.20, and plot on a 0.45 power gra- dation chart. What is the maximum size? What is the nominal maximum size? TABLE P5.20 Sieve Size 37.5 mm 25 mm 19 mm 9.5 mm 4.75 mm 0.60 mm 0.075 mm Pan Amount Retained, g 0 315 782 1493 677 1046 1502 45 Cumulative Amount Retained, g Cumulative Percent Percent Passing Retained
Notice: This is only for REVIEW PURPOSES, this is NOT GRADED. A 100 block is in equilibrium. What is the magnitude of the frictional force between this block and the surface? Given: Us = 0.3 2 lb Options: A. 0 lb B. 1 lb C. 2 lb D. 3 lb E. Othe answer
Help asnwer this, thanks.
The base has an average thickness of 8 inches and a density of 110 pounds per cubic foot. The curb is 6 inches wide and has an inside radius of 5 feet. Determine the tons of base required.
The following diagram shows a partial floor framing plan of an elevated walkway building connecting an airport terminal building to the adjacent garage. The concrete floor is not post- tensioned. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Framing members are not exposed to weather or in contact with soil. Per the ACI, what is the minimum slab depth? Consider both the interior slab and the cantilevered slab at the edge of the building. 30-0¹ B4 B4 B4 83 Column 52 SI 30-0 -Sab Mark Dean- B4 B4 B4 83 B 30-0¹ BI B2 B2 BI -Girder 12 A 1 3-4 Ei 13:4 05 40-0 to 2
I need the answer as soon as possible