A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) on a section 2.49 m from A if P = 5105 N, W = 2009 N/m, a = 0.72 m, b = 1.19 m, c = 0.98 m, L = 76 mm and h = 216 mm. Round off the final answer to two decimal places. W +²+ comptation A C B b ➜ h

A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) on a section 2.49 m from A if P = 5105 N, W = 2009 N/m, a = 0.72 m, b = 1.19 m, c = 0.98 m, L = 76 mm and h = 216 mm. Round off the final answer to two decimal places. W +²+ comptation A C B b ➜ h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i will upvote who can answer this
Calculate the nominal moment strength of a reinforced concrete beam 270 mm x 490 mm if at failure the concrete compression strain is 0.003 and the tensile steel strain is 0.005. The flexure bars are 16 mm in diameter enclosed by 10 mm stirrups. Use f'c = 27 MPa and fy = 420 MPa. Express your answer as a whole number in the unit of kN.m.
i will upvote who can answer this
Problem 3- The shown aluminum block with a rectangular cross section in subjected to a compressive axial force of 8 kips. If the 1.5 inch side changed its length to 1.500132 inches, determine: 1-Poisson's ratio. 2-The new length of the 2 inch side. 1.5 in. 8 kip- E=10,000 Ksi 8 kip
5.
i will upvote who can answer this
Home Work 10.4-1 Elongation-tensile force data for the aluminum specimens of Home Work 10.3-1 has been represented as indicated. Determine the equation of regression line. Ans. A = -2.4+10.83F where A is the elongation in inch, and F is the force in kips. Tensile Force in kips, X 1 3556NH 2 4 6 Elongation in 10³ of inch, Y 9 20 28 41 52 63
answer A only . Answer just by virtual work method
my answer is wrong please help me solve
Express your answer in 3 decimal places.
Consider the Fink truss shown in (Eigure 1). Suppose that Fi=600 lb and Fy=900 lb. Figure 1 of 1 K60 60% -100- Determine the force in the member GF of the truss and state if the member is in tension or compression. Express your answer using three significant figures. Enter negative value in the case of compression and positive value in the case of tension. VAZ vec For= lb Submit Request Answer • Part B Determine the force in the member FB of the truss and state if the member is in tension or compression. Express your answer using three significant figures. Enter negative value in the case of compression and positive value in the case of tension. VAX Ivec Fre lb Previous Answers Request Answer Submit
A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in the z direction. The block is subjected to a triaxial loading of three resultant forces as follows: 70 kips compression in the x direction, 55 kips tension in the y direction, and 48 kips tension in the z direction. If ν = 1/3 and E = 29 x 106 psi, ( a ) determine the single resultant load in the z direction that would produce the same deformation in x direction as the original loadings, ( b ) determine the single resultant load in the y direction that would produce the same deformation in z direction as the original loadings, and ( c ) determine the single resultant load in the x direction that would produce the same deformation in y direction as the original loadings.