A vertical channel 152 x 76 (see Table A-7) has a cantilever beam bolted to it as shown. The channel is hot-rolled AISI 1006 steel. Thebar is of hot-rolled AISI 1015 steel. The shoulder bolts are M10 x 1.5 ISO 5.8. Assume the bolt threads do not extend into the joint. For adesign factor of 2.2, find the safe force Fthat can be applied to the cantilever.1250+50--50-- 26!125The maximum allowable force on the system FisN.

Answered: Image /qna-images/answer/3426d035-88df-4eaa-a846-a614f76594d0.jpg

A vertical channel 152 x 76 (see Table A-7) has a cantilever beam bolted to it as shown. The channel is hot-rolled AISI 1006 steel. The bar is of hot-rolled AISI 1015 steel. The shoulder bolts are M10 × 1.5 ISO 5.8. Assume the bolt threads do not extend into the joint. For a design factor of 2.2, find the safe force Fthat can be applied to the cantilever. 12 50 +50 -50 125 The maximum allowable force on the system Fis |N.

A vertical channel 152 x 76 (see Table A-7) has a cantilever beam bolted to it as shown. The channel is hot-rolled AISI 1006 steel. The bar is of hot-rolled AISI 1015 steel. The shoulder bolts are M10 × 1.5 ISO 5.8. Assume the bolt threads do not extend into the joint. For a design factor of 2.2, find the safe force Fthat can be applied to the cantilever. 12 50 +50 -50 125 The maximum allowable force on the system Fis |N.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q/ Figure below shows the load components acting on a helical gear mounted on a simply supported…

A: Given data Diameter of the shaft =20 mm Ry1+Ry2=2KN2×127+68.42=Ry2×177Ry2=322.42177=1.8215…

Q: the diagram below shows a circula bar , made of AISI 1040 OQT 1300 steel (SU = 600 MPa), is loaded…

Q: Select a standard threaded round rod to support a factored tensile load of 35 kips (service tensile…

A: Given: The fractured load, Pf = 35 kips The service load, Ps = 25 kips The yield strength of A36…

Q: What is the largest force that can be applied to the part? The largest force that can be applied is…

Q: Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a…

A: Steel plates of size 14 in × 8 in of A 36 steel Ultimate tensile strength of A 36 steel is…

Q: For a bolted assembly with 8 bolts, the stiffness of each bolt is k_b = 1.1 N/mm and the stiffness…

A: Question is solved below Explanation:To find the maximum safe working load for the bolted assembly,…

Q: A course pitch metric grade 9.8 bolt with a hexagonal nut assembly is used to keep two machined…

A: Step 1: Step 2: Step 3: Step 4:

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2-…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: Problem 3: A Hexagonal bolt connects two members. The joint has a gap 1 = 2 in and the applied load…

A: Given data: The gap (or) length of the bolt, l = 2 in Applied load, P = 2000 lb 5/16 in 18 UNC-2A…

Q: An M 14 x 2 hex-head bolt with a nut and a 14R washer under each of bolt head and the nut is used to…

A: Step-3: kb=(153.9×7)+(115×26)153.9×115×207=653.48mMN…

Q: The figure shows a connection that employs three SAE grade 4 bolts. The tensile shear load on the…

A: From Table 8-9: for SAE Grade 4 boltsFrom Table A-20: for AISI 1020 HR

Q: Compute the design factor in the middle portion only of the rod AC if the steady vertical force on…

Q: 40 kN/m C D 4 m El = constant B 100 kN 2 m A |-1.5 m- 5 m

A: This Question belong to complex In determinant beams so that for solution it can be observed about 2…

Q: The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load…

A: Given kb = 8 Mlb/in km = 18 Mlb/in Bolt Size = 5/8 in Fatigue design factor = 2.5 To find Repeated…

Q: 10) A screw clamp similar to the one shown in the figure has a handle with diameter in made of…

A: Given Screw clamp To find Torque it can handle

Q: For a bolted assembly with four bolts, the stiffness of each bolt is kb = 3.0 MN/mm and the…

Q: repeat problem 8-19 with the bottom aluminum plate replaced by one that is 20 mm thick.

A: The total grip length is the sum of the thicknesses of the plates being clamped together. In this…

Q: = 3) A double screw (Acme thread angle o 14.5) mechanism is designed to lift a load of 18,000 lb in…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: The two lever assembly shown below is subject to a static load F = 8250 lb. (a) identical links BD…

A: Given:

Q: Condition #1: Å structural support for a machine is subjected to a static compression load of 20 kN.…

Q: For a bolted assembly with six bolts, the stiffness of each bolt is kb = 1.8 Mlbf/in and the…

A: If you have any doubts,do write in comments.

Q: Use LRFD and design a 13-foot-long tension member and its connection for a service dead load of 8…

A: Equilibrium is a state of a body at which there is no disturbance in a system neither inside nor…

Q: ZL.m An M8x1 bolt joins to members of 40 mm total thickness. The bolt and members are made of the…

Q: Part A Determine the smallest diameter of the rod that will support the load ofP = 3.4 kip without…

Q: A factor of safety of 2.5 is used for the bolts in the assembly below. The ultimate shear stress of…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

A vertical channel 152 x 76 (see Table A-7) has a cantilever beam bolted to it as shown. The channel is hot-rolled AISI 1006 steel. The
bar is of hot-rolled AISI 1015 steel. The shoulder bolts are M10 x 1.5 ISO 5.8. Assume the bolt threads do not extend into the joint. For a
design factor of 2.2, find the safe force Fthat can be applied to the cantilever.
12
50
+50--50-- 26!
125
The maximum allowable force on the system Fis
N.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Qestion-1: A 9/16 in UNF bolt is subjected to a load P = 60 kip in a tension joint as shown in Figure. The bolt is SAE grade 5 and lubricated. The initial bolt tension (F) = 35 kip. The bolt and joint stiffnesses are k, = 6.5 and km 10.8 Mlbf/in Note: Use the related tables, formulas and concepts to answer following question (a) Formulate to determine the preload and service load stresses in the bolt. (b) Solve to find the torque necessary to develop the preload. (c) Identify if the bolt will fail or no under preload and service load stresses (Calculated in part a) by comparing with the SAE minimum proof strength of the bolt. (d) Can you identify; with given input data, tables and formulas that bolt is self-locking? Table 8-9 SAE Specifications for Steel Bolts Size SAE Range Grade Inclusive, No. in +14 1 2 4 5 5.2 7 8 TI I LI I I I +-14 8.2 -1 Minimum Proof Strength," kpsi 33 55 33 65 85 74 85 105 120 120 Table 8-2 Diameters and Area of Unified Screw Threads Size Designation 0 1 2 3 4…
Required information A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±1.7 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 5 x 104 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end. Determine the endurance limit for this application. Assume that the size modification factor kis 0.85 until a size for the section is known. The endurance limit is 278.4 MPa.
For the frame shown in Fig. 6-24a, draw the free-body diagrams of (a) the entire frame including the pulleys and cords, (b) the frame without the pulleys and cords, and (c) each of the pulleys. 3E Fx=0 +9 E fy=o 1. FIMD RXAS AT A$D Fing FoRLE componeAB 2. Ge Pits oF POLLEYS EM=0 Cx C By E Ay T. Ay AauLE OF RESOUTAT AT B, C &A 75 lb SKETCH RESULTALT (a) Fueo Manat AT BASE ア(y 7516 OF CULUneCE radius of the pulley at B linch Yadius of the Pulley at c a7s inch 75 lbs 7516 () Distance BE 7inch Distance EA 4.5 inch Distance AV : 3.sinch Ay 6) 7516 マへ
(15) A 3/8 - x 2-in AISI 1018 cold-drawn steel bar is cantilevered to support a static load of 300 lbf as illustrated. The bar is secured to the support using two 1/2 in-13 UNC SAE 5 bolts. Find the factor of safety for the following modes of failure: shear of bolt, bearing on bolt, bearing on member, and strength of member. (Ans/ 5.79, 9.58, 5.63, 295) in 3 in l in 14 in 300 Ibf
The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load imposed on it. The bolts are -in coarse-thread SAE grade 8, tightened to recommended preload for nonpermanent assembly. The stiffnesses have already been computed and are kp=4 Mlb/in and km = 16 Mlb/in. Laad line F. Steady stress (a) Assuming that the bolts, rather than the welds, govern the strength of this design, determine the safe repeated load that can be imposed on this assembly using the Goodman criterion with the load line in the Figure and a fatigue design factor of 2. (b) Compute the static load factors based on the load found in part (a). (ie. Yielding factor of safety, Load factor of safety and factor against joint separation)
Required information The bolted connection shown in the figure is subjected to a tensile shear load of 90 kN. The bolts are ISO class 5.8, and the material is cold-drawn AISI 1015 steel. Assume the bolt threads do not extend into the joint. Find the factor of safety of the connection for all possible modes of failure. Give the overall joint factor of safety. Given: t = 15 mm and t2 = 25 mm. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 35 60 60 - 35 t1 M20 x 2.5 35 35 + t2 Find the overall joint factor of safety. The overall joint factor of safety noverall is
Calculate external support reactions, forces of internal joints and draw FBD of assembly
Required information For a bolted assembly with six bolts, the stiffness of each bolt is kb 2 Mibf/in and the stiffness of the members is km = 13 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. It is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts once the load is applied. The maximum bolt preload that can be applied is Ibf.
Required information A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±1.7 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 5 x 104 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end. What will the strength of the metal be at 5 x 104 cycles? The strength of the metal at 5 x 104 will be MPa.
The figure illustrates the connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure pg. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes in Table A–17, then determine the yielding factor of safety np, the load factor nL, and the joint separation factor n0. See problem number 8-36, and please use the FEA exponential curve-fit for member stiffness.
The cantilever bracket Is bolted to a column with three M12 x 1.75 ISO 5.8 bolts. The bracket Is made from AISI 1020 hot- rolled steel. Assume the bolt threads do not extend into the Joint. Find the factors of safety for the following fallure modes: shear of bolts, bearing of bolts, bearing of bracket, and bending of the bracket. GIVE the overall jolnt factor of safety. Given: F= 2 KN. NOTE: This is a multi-part questlon. Once an answer Is submitted, you will be unable to return to this part. Holes for M12 x 1.75 bolts 8 mm thick 36 32 36 - 200- Column Find the factor of safety with respect to the shear stress In the bolts. The factor of safety with respect to the shear stress In the bolts ng Is 4.4
8-75 A vertical channel 152 X 76 (see Table A–7) has a cantilever beam bolted to it as shown. The channel is hot-rolled AISI 1006 steel. The bar is of hot-rolled AISI 1015 steel. The shoulder bolts are M10 × 1.5 ISO 5.8. Assume the bolt threads do not extend into the joint. For a design factor of 2.0, find the safe force F that can be applied to the cantilever. 8T-8 12 Problem 8-75 in millimeters. 50 -50→-50→261! 125 000