(15) A 3/8 - x 2-in AISI 1018 cold-drawn steel bar is cantilevered to support a static load of 300 lbf as illustrated. The bar is secured to the support using two 1/2 in-13 UNC SAE 5 bolts. Find the factor of safety for the following modes of failure: shear of bolt, bearing on bolt, bearing on member, and strength of member. (Ans/5.79, 9.58, 5.63, 2.95) in 3 in l in 14 in 300 Ibf

(15) A 3/8 - x 2-in AISI 1018 cold-drawn steel bar is cantilevered to support a static load of 300 lbf as illustrated. The bar is secured to the support using two 1/2 in-13 UNC SAE 5 bolts. Find the factor of safety for the following modes of failure: shear of bolt, bearing on bolt, bearing on member, and strength of member. (Ans/5.79, 9.58, 5.63, 2.95) in 3 in l in 14 in 300 Ibf

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A NON- permanent bolted joints carrying tension load and has a stiffness constant of C= 0.2 the joint is using an MI4 X ISO 9.8 bolt . the bolt is subject to a repeated load of Pmax= 30KN. Find the factor of safety based on goodman theory, and also check the possibility of yielding .
4 dia 16 R. 3. The grip strengthener shown in Fig. 1 is composed of a helical spring made of 4 mm diameter A227 hard-drawn Wire clip wire. The main coil has an outer diameter OD = 32 mm and a total number of body turns N= 3.5. During operation, assume that the force applied to the handles Molded 112.5 plastic handle 87.5 occurs at a distance of 50 mm from the base of the handle. Using a design factor at closure of n, = S,lo,= 1.1, calculate the torsional spring constant k' and the force F, required to close the handles. 75 Fig. 1
The crank of jib crane model J-06T is fixed at one end and hinged to a pivot pin. The crank is 300 in and 5” in diameter. Assuming carbon –alloy steel (E = 29,000 ksi) What is the safe working compressive load on the crank at FS = 4?
i need the answer quickly
8-68 Engineering Design + 40 1 plem 8-68 70 millimeters. 40 A bolted lap joint using ISO class 5.8 bolts and members made of cold-drawn SAE 1040 steel is shown in the figure. Assume the bolt threads do not extend into the joint. Find the tensile shear load F that can be applied to this connection to provide a minimum factor of safety of 2.5 for the fol- lowing failure modes: shear of bolts, bearing on bolts, bearing on members, and tension of members. 20 M20x2.5 20
mechanical design
Please help provided all that is needed, all analysis etc. Thank you
A helical compression spring has a scale of 400 lb/inch, an inside diameter of 2.5 inches, a free length of 8 inches and with squared and ground ends. Material is to be chrome vanadium steel. For a load, P, of 750 pounds, and for average service, determine the solid height. Working stress is 63 ksi, G = 10,800 ksi.
P
Qestion-1: A 9/16 in UNF bolt is subjected to a load P = 60 kip in a tension joint as shown in Figure. The bolt is SAE grade 5 and lubricated. The initial bolt tension (F) = 35 kip. The bolt and joint stiffnesses are k, = 6.5 and km 10.8 Mlbf/in Note: Use the related tables, formulas and concepts to answer following question (a) Formulate to determine the preload and service load stresses in the bolt. (b) Solve to find the torque necessary to develop the preload. (c) Identify if the bolt will fail or no under preload and service load stresses (Calculated in part a) by comparing with the SAE minimum proof strength of the bolt. (d) Can you identify; with given input data, tables and formulas that bolt is self-locking? Table 8-9 SAE Specifications for Steel Bolts Size SAE Range Grade Inclusive, No. in +14 1 2 4 5 5.2 7 8 TI I LI I I I +-14 8.2 -1 Minimum Proof Strength," kpsi 33 55 33 65 85 74 85 105 120 120 Table 8-2 Diameters and Area of Unified Screw Threads Size Designation 0 1 2 3 4…
Required information A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±1.7 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 5 x 104 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end. Determine the endurance limit for this application. Assume that the size modification factor kis 0.85 until a size for the section is known. The endurance limit is 278.4 MPa.
Required information The cold-drawn AISI 1040 steel bar shown in the figure is subjected to an axial load that fluctuates from 8 kN to 30 kN. Use the Modified Goodman criterion and estimate the fatigue factor of safety based on achieving infinite life and the yielding factor of safety. 25 mm 10mm -6-mm D. What is the number of cycles to failure for this part? The number of cycles is 120000