A uniform beam weighing 500 N is held in a horizontal position by three vertical wires, one attached to cach end of the beam, and one at the mid-length. The outer wires are brass of diameter 0.125 cm, and the central wire is of steel of diameter 0.0625 cm. If the beam is rigid and the wires are of the same length, and unstressed before the beam is attached, estimate the stresses in the wires. Young's modulus for brass is 85 GN/m' and for steel is 200 GN/m. Brass Stel Brass 500N

A uniform beam weighing 500 N is held in a horizontal position by three vertical wires, one attached to cach end of the beam, and one at the mid-length. The outer wires are brass of diameter 0.125 cm, and the central wire is of steel of diameter 0.0625 cm. If the beam is rigid and the wires are of the same length, and unstressed before the beam is attached, estimate the stresses in the wires. Young's modulus for brass is 85 GN/m' and for steel is 200 GN/m. Brass Stel Brass 500N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 67 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E = 180 GPa. Assume a = 3.1 m, b = 1.3 m, and c = 1.3 m. What is the magnitude of load P that is necessary to displace point A 10 mm to the left?
Problem 6. Solve the average normal stress occurring in each steel wire shown in the figure. Assume a 500-kg load being supported by wires all 3 having a diameter of 5 mm each. -600 mm- -600 mm- A 800 mm
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure given. Axial loads are applied at the positions indicated. If P = 3000 Ib and the cross sectional area of the rod is 0.5 in?, determine the stress in each section. 4P Steel Bronze Aluminum P 2 ft 3 ft 2.5 ft
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 17 mm and an elastic modulus of E = 71 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E = 190 GPa. Assume a = 3.1 m, b = 1.7 m, and c = 0.9 m. What is the magnitude of load P that is necessary to displace point A 8 mm to the left?
A beam having the cross section shown is subjected to a couple M0 acting in a vertical plane. Determine the largest permissible value of the moment M0 of the couple if the maximum stress is not to exceed 103 MPa. Given: Iy = Iz = b4/36 Iyz = b4/72
Q- A uniform prismatic circular bar made up of rigid material is subjected to a tensile force of 5000 N at one end. If the diameter of the cross-section is 7 mm, then find the stress and strain in the bar.
For the beam geometry shown, determine the following: a. Cracking moment b. Has the beam section already cracked? c. Determine the bending stresses at the extreme fibers of the beam. Applied moment = 34kN/m fc = 21 MPa As = 1935mm² n=9 250mm 00 400mm 75mm
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in bronze bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 144.21 102.49 341.33 54.56
Determine the tensile strain Original length L = 500 mm Tensile deformation = 2.5 mm
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 13 mm and an elastic modulus of E = 70 GPa. The steel rod has a diameter of 20 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.9 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 14 mm to the left? a b (1) P Answer: P = i (3) B KN O
thank you. Civil engineering - strength of materials
4 A metal wire Im long and of 10mm diam eter is stretched by a load of 50 kg. If E = 7 x 10³ N/mm² for the metal, find the (a) stress (b) strain and (3) Poisson's ratio if the lateral strain is 2.6x 105 m/m.