Determine the largest weight W which can be supported by the two wires shown. The stresses in wires AB and AC are not to exceed 150 MPa and 100 MPa, respectively. The cross-sectional areas of the two wires are 400 mm2 for wire AB and 200 mm2 for wire AC. Answer must be in kN and please indicate it in your answer. 30° 50° W

Determine the largest weight W which can be supported by the two wires shown. The stresses in wires AB and AC are not to exceed 150 MPa and 100 MPa, respectively. The cross-sectional areas of the two wires are 400 mm2 for wire AB and 200 mm2 for wire AC. Answer must be in kN and please indicate it in your answer. 30° 50° W

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Item 4 (Figure 1) Figure 1 W of 1 X Part A Replace the loading by an equivalent force. Express your answer to three significant figures and include the appropriate units. FR Submit Part B μÅ Value Units MRO Replace the loading by a couple moment acting at point O. Express your answer to three significant figures and include the appropriate units. = My Answers Give Up HÅ ? Value Units ?
A compressed liquid is a cylinder that has a volume of 0.400 m ^ 3 at 70Pa and a volume of 0.396m ^ 3 at a pressure of 140Pa. Determine the modulus of volumetric elasticity.
for part C where did L/4 come from? and why is it that when you subtract it its wL^2/8 and -wL^2/4?
Rough cost estimate can provide quick cost value to the estimator. true or false?
Solve equations 1 and 2 shown below. All the values are given below please subsitute in the two equations and solve for P. The value of P must be in kips. Pls show all calculations along with units. Also solve for Wdl (I have put a question mark next to it under Given section), must be in PLF. thanks in advance will give a thumbs up and good rating. the same question was answered wrong last time, Sx was considered. u dont need Sx, Ma/ohm as a whole is 8.71k - ft. The value of P shouldnt be negative.Thats why use proper units
Fill in the table :
give at least 3 applications each for Unit Weight and Specific Gravity of Aggregates for Engineering. You can use either of the 5 Divisions of Engineering: Structural, Construction, Water and Hydraulics, Geotechnical, and Transportation.
Consider the material Al-$456 It has the following physical plopertes Oyield=230mPa 5=-726PA (modulos elesticity). G- 28GPA (mad ulus Cigidity) Oultimate=315mPA Tuield=130 mPa Toltimate=185 mPA A) Calculate Poisson's ratio 3-0 block of Al-5456 wwith the BIf we have a following dimensions And Ferces =80ON Ex = X= Bcm Fy= 1000N y=4cm =1400N c) Is our block safe? (conside only plane stess) D)set up the 3 eqetions to find the strains (EEg t2) in each direction ESolve the3equations to find the Enal dimensions OF our blocK
I need hand written solution only
All answers should be in 2 decimals places
GIVEN: diameter of sewer pipe = 1.8mDepth of water = 1.6mQ = 2.5m3/sCompute the velocity. Use 3 decimal places all throughout the solution. Box/underline your finalanswer.
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 520 psi in size. (a) Determine the stresses Ox, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). X Ø C y b