2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free. What is the largest load P that can be applied without exceeding stresses of 160 MPa in the steel rod and 65 MPa in the bronze rod? - 2.5 m 2 m 2 m Steel A=1000 sq. mm Bronze A=400 sq. mm E=200 GPa E=83 GPa L=1.6 m L=2.2 m P

2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free. What is the largest load P that can be applied without exceeding stresses of 160 MPa in the steel rod and 65 MPa in the bronze rod? - 2.5 m 2 m 2 m Steel A=1000 sq. mm Bronze A=400 sq. mm E=200 GPa E=83 GPa L=1.6 m L=2.2 m P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: 5 The supports of Beam AD are aluminum rod and st eel rod only. Determine the stress in the aluminum…

Q: Which statement about perforation plates is FALSE? Perforation plate type may help in identification…

A: c. The foraminate perforation plate looks like a ladder is false. A foraminate perforation plate is…

Q: A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two-…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: The given data is shown below: Diameter of aluminium rod=19mmElastic modulus=69 GPaDiameter of steel…

Q: A 10 cm diameter solid alumin Assume that L=0.5 m. The yiel a) Normal stress due to bending caused…

Q: Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the…

Q: A steel rod 26 mm diameter has a brass sleeve 40 mm external diameter and 26 mm internal diameter…

A: Axial deformation in a bar takes place due to axial force. The axial force depends upon the…

Q: Three round bars welded together axially loaded as shown. Find the normal are stress in each bar if…

A: Stress is defined as the force acting per unit area of a bar. The stress in a bar is directly…

Q: The temperature of the cylindrical rod is heated to 45°C which is fixed in between A and C rigid…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that
the rods were initially stress-free. What is the largest load P that can be applied without
exceeding stresses of 160 MPa in the steel rod and 65 MPa in the bronze rod?
- 2.5 m
2 m
2 m
Steel
A=1000 sq. mm
Bronze
A=400 sq. mm
E=200 GPa
E=83 GPa
L=1.6 m
L=2.2 m
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
need help.
Determine the normal stress and change in length of the aluminum rod if the temperature was raised by 125°C. The 0.5-mm gap exists at 20°C. q = 5 t = 0
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the temperature is 20°C, there is no stress in the bar. Compute the stress developed in the beam if the temperature rises to 45°C. Assume that the proportional limit is 235 MPa. a = 11.7 x 10-6 1/C° E = 207 GPa 4. In question 3, assume that the bar is free to elongate or shorten, calculate the change in the length of the bar if the temperature drops from 20°C to -20°C.