A three phase 410 volt (line voltage) distribution system feeds power to a household load. Each phase of the system (distribution line) has an impedance consisting of a resistance (0.502) and a reactance (0.5) (inductive). The system is connected to three-phase load with an impedance of j + 702 in a delta connection. What is the active, reactive and apparent power of the load (notice that distribution line impedance is not part of the load)? Give the answers to two decimal places. a) Absolute value of current feeded by the voltage source. I = b) Active power P = c) Reactive power Q = d) Apparent power S (absolute value) = kW kV Ar kVA A

A three phase 410 volt (line voltage) distribution system feeds power to a household load. Each phase of the system (distribution line) has an impedance consisting of a resistance (0.502) and a reactance (0.5) (inductive). The system is connected to three-phase load with an impedance of j + 702 in a delta connection. What is the active, reactive and apparent power of the load (notice that distribution line impedance is not part of the load)? Give the answers to two decimal places. a) Absolute value of current feeded by the voltage source. I = b) Active power P = c) Reactive power Q = d) Apparent power S (absolute value) = kW kV Ar kVA A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Consider a building with a real power demand of 650 kW and reactive power demand of 480 KVAR. Determine the current power factor and then find the required size of a set of capacitors to be installed in parallel with the building service entrance so that the power factor becomes at least 0.90.
Power factor correction is a method to do which of the following.
Three Impedances each of (9 - j18)N are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
The figure shows a 3-phase bala Time left 1:06:30 200 /00 Vrms. sequence electrical system. Vcn Vbn %3D al Balanced (-) sequence 100 so a 2000 Vms Select one: O a. 200 /-120 Vrms O b. 200 v2 /0 Vrms O C. 200 /0 Vrms O d. 200 v2/-120 Vrms e. 200/120 Vrms
1) Determine the total current supplied by the source and the current in each branch. 2) Sketch a fully labelled phasor diagram showing all voltage and currents in the circuit. 3) Determine the active power delivered by the source voltage. 4) Determine the reactive power. 5) Sketch the power triangle. 6) Comment on the significance of the power factor and briefly state how it can be improved.
IL 220230° Load P = 2 kW pf = 0.9 lag Assuming that the source is operating at 60 Hz, determine the following: a.) The value of the current I, in phasor form the magnitude, degrees for the angle) b.) What is the reactive power Q of the load in (volts for KVAR? c.) Is the load consuming or supplying Q? d.) What is the apparent power S of the load in KVA? e.) What is the load resistance? Express your answer in Ohms. f.) What is the load inductance? Express your answer in millihenries.
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following: e. Reactive power supplied by the sourcef. Apparent power of the circuitg. Power factor of the entire circuit
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
A 25 kVA, 240 V single phase source supply the rated power at the rated voltage to a motor at 0.8 power factor lagging. Find the capacitor bank in order to improve the power factor to 0.9 lagging. connected to a motor. a. Calculate the real power, reactive power and current before capacitor bank is connected? P= Q= b. Calculate the power and reactive power after capacitor bank is connected? P = c. What is kVA rating of capacitor bank Qc?
A three phase 390 volt (line voltage) distribution system feeds power to a household load. Each phase of the system (distribution line) has an impedance consisting of a resistance (0.602) and a reactance (0.40) (inductive). The system is connected to three-phase load with an impedance of j +62 in a delta connection. What is the active, reactive and apparent power of the load (notice that distribution line impedance is not part of the load)? Give the answers to two decimal places. a) Absolute value of current feeded by the voltage source. I = 3.62 A Your last answer was interpreted as follows: 3.62 b) Active power P = c) Reactive power Q = d) Apparent power S (absolute value) kVA = kW kV Ar 4
Three identical Y-connected loads, each having a resistance of 20 22 in parallel with an inductor, are connected to a three phase supply of 400 V and 50 Hz frequency. The power absorb by the load is 8 kW and power factor at the load is 0.9919. (i) Determine the current that flows through the inductor. Please state the assumptions used to solve the question. Calculate load inductance in Henry (H).