A three phase 390 volt (line voltage) distribution system feeds power to a household load. Each phase of the system (distribution line) has an impedance consisting of a resistance (0.60) and a reactance (0.40) (inductive). The system is connected to three-phase load with an impedance of j +62 in a delta connection. What is the active, reactive and apparent power of the load (notice that distribution line impedance is not part of the load)? Give the answers to two decimal places. a) Absolute value of current feeded by the voltage source. I = 3.62 A Your last answer was interpreted as follows: 3.62 b) Active power P = c) Reactive power Q d) Apparent power S (absolute value) = = kVA kW kV Ar 4

A three phase 390 volt (line voltage) distribution system feeds power to a household load. Each phase of the system (distribution line) has an impedance consisting of a resistance (0.60) and a reactance (0.40) (inductive). The system is connected to three-phase load with an impedance of j +62 in a delta connection. What is the active, reactive and apparent power of the load (notice that distribution line impedance is not part of the load)? Give the answers to two decimal places. a) Absolute value of current feeded by the voltage source. I = 3.62 A Your last answer was interpreted as follows: 3.62 b) Active power P = c) Reactive power Q d) Apparent power S (absolute value) = = kVA kW kV Ar 4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Three-phase electricity is delivered to a factory 7 km from a distribution company. The factory receives a total of 2000 kW of power at a voltage of 10.98 kV (rms) per phase. If the transmission cable in each phase has a resistance of 1.8 per 10 km, then the total power lost in the cables of this three-phase system is (a) 4.645 W (b) 13.93 W (c) 4.645 kW (d) 13.93 kW
Three Impedances each of (9 - j18)N are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
A load of 138+j460 Ohm is supplied through 3+j14 Ohm line as shown in Figure 1. (a) Find the average power dissipated in the line. (b) Find the value of capacitive reactance connected across the load to compensate the reactive power need of the load. (c) What is the equivalent impedance after compensation. (d) Find the average power dissipated in the line when the capacitive reactance is connected across the load. (e) Express the power loss in (d) as a percentage of the power found in (a) j14 Figure 1 7200/0 + V (rms) Source 3 wi Line Load 138 j460
.............. compensators are connected at receiving end to generate reactive power to the line.
IL 220230° Load P = 2 kW pf = 0.9 lag Assuming that the source is operating at 60 Hz, determine the following: a.) The value of the current I, in phasor form the magnitude, degrees for the angle) b.) What is the reactive power Q of the load in (volts for KVAR? c.) Is the load consuming or supplying Q? d.) What is the apparent power S of the load in KVA? e.) What is the load resistance? Express your answer in Ohms. f.) What is the load inductance? Express your answer in millihenries.
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
4
Describe the concept of three-phase power in electrical systems and its significance in power distribution.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
A 25 kVA, 240 V single phase source supply the rated power at the rated voltage to a motor at 0.8 power factor lagging. Find the capacitor bank in order to improve the power factor to 0.9 lagging. connected to a motor. a. Calculate the real power, reactive power and current before capacitor bank is connected? P= Q= b. Calculate the power and reactive power after capacitor bank is connected? P = c. What is kVA rating of capacitor bank Qc?
2. A single-phase a.c. distributor AB is fed from end A and has a total impedance of (0-2 + j 03) ohm. At the far end, the voltage V = 240 V and the current is 100 A at a p.f. of 0-8 lagging. At the mid-point M, a current of 100 A is tapped at a p.f. of 0-6 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and Vg- [292 V, 2-6°] a loade
Three identical Y-connected loads, each having a resistance of 20 22 in parallel with an inductor, are connected to a three phase supply of 400 V and 50 Hz frequency. The power absorb by the load is 8 kW and power factor at the load is 0.9919. (i) Determine the current that flows through the inductor. Please state the assumptions used to solve the question. Calculate load inductance in Henry (H).