2. A voltage applied to a load is V=208420°V and current through load is I=10 &-10° A.Find the following [SO 1]o complex power consumed by load• Is the load inductive or capacitive?o the power factor of the loado the reactive power consumed or generated by the load.o Does the load consume or supply reactive power?3. A single phase motor draws 20 kVA at 0.70 lagging power factor from a 120 V source. ThePUD desires to improve the power factor to 0.9 lagging by connecting a shunt capacitor bankacross the terminals of the motor. Determine the size of the capacitor bank in VARS. Calculatethe following: [SO 1]a)What are the initial load current, real and reactive powers of the load?b)What are the real and reactive power after adding the capacitor bank?c)What is the kVAr rating of the capacitor bank? (3)d) What is the load current?di) How is the load current affected by the load reactive power?

Answered: ductive or tor of the ower cons consume

Engineering

Electrical Engineering

ductive or tor of the ower cons consume

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

A single-phase motor draws 220 W at a power factor of 0.8 lagging when connected across a 240 V rms, 60-Hz source. A capacitor is connected in parallel with the load to produce a unity power factor. Determine the required capacitance.
A three-phase star-connected alternator delivers at rated load a current I = 200 A under a voltage of 5 kV-50 Hz (between phases). The load is inductive of power factor equal to 0.87, the resistance of each stator winding is 0.292 and the speed of the rotor is n = 750 r.p.m. The sum of the constants losses and the stator Joule's losses and the rotor Joule's losses is 55 kW. The no load test, at rated frequency, gave: E-4200 V (between phases) for an excitation current lexc = 40 A. The short-circuit test, for an excitation current lexc = 40 A, gave a short-circuit current in the stator windings Ise =2.5 kA. 1- Calculate the numbers of poles of the alternator. 2- Calculate the synchronous reactance (X). 3- Calculate the electromotive force of the alternator (E) between phases for the same excitation current. 4- Calculate the power absorbed by the alternator (Pa).
Please i want the answer son as possible
Alternator A (100 kVA, 3-f, 240 V, 60 Hz, 1800 rpm) is operating in parallel with alternator B (125 kVA, 3-f, 240 V, 60 Hz, 1800 rpm). The load of alternator A is 70 kW at 85% pf leading and the load of alternator B is 85 kW at 75% pf leading. Determine the pf of load.
A synchronous generator may be represented by a voltage source of magnitude 1.7 p.u. in series with an impedance of 2 p.u. It is connected to a zero-impedance voltage source of 1 p.u. The ratio of X/R of the impedance is 10. Calculate the power generated and the power delivered to the voltage source if the angle between the voltage sources is 30°.
A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is Vs = 230 V, 60 Hz. The delay angle is 120 degree. Then power factor of the circuit is: Select one: O a. 1 O b. 0.75 O c. 0.44 O d. None of the above O e. 0.9
5) A balanced three-phase source of 4160 V is feeding a balanced three-phase induction motor through a cable of negligible impedance. The induction motor draws 400 kW at 0.8 power factor lagging. Calculate the reactive power consumed by the induction motor. Design two different techniques to improve the overall power factor from 0.8 to 0.96 lagging. Show the effectiveness of your design through a numerical example. i) ii)
A synchronous generator is generating 395 V at 55 Hz at a field current of 3A. The e.m.f generated when the frequency is 35HZ and the field current is 2.3A is ..............
3. A 12020⁰ Vrms is to supply power to a welder, heater and an induction motor. A welder is a coil of (4+j3) ohm, the induction motor draws 60KW with 0.8 power factor, and the heater is a resistor that draws 15KW power. Find the complex power, real power, reactive power and the total power factor that must be supplied by source. If a capacitor will be used to supply a reactive power in the circuit in order that the net load will have a unity power factor, what reactive power must be supplied by the capacitor? Draw the circuit.
a) An electrical engineer is assigned to analyze the generator specification that produces a sinusoidal wave with no phase angle. The maximum e.m.f value of the generator is 120V over the period, T = 250 ms. i. Calculate the e.m.f value at coil position 80° and 1.75x rad. Determine the generated e.m.f at t = 150 ms. ii. ii. If the phase angle of the generator shifted to –25° during the measurement process. Evaluate the time, to produce the instantaneous e.m.fof 67V .
A single-phase motor draws 180 W at a power factor of 0.8 lagging when connected across a 240 Vrms, 60-Hz source. A capacitor is connected in parallel with the load to produce a unity power factor. Determine the required capacitance. The required capacitance = ____ μF.
V1 = 170 V f1 = 100 Hz 1) A single-phase load has an active power of P = 2 kW at V1 V @f1Hz and the power factor is cosφ = 0.75. This motor iscompensated to cosφ = 0.85 using a parallel capacitor Find the reactive power difference between compensated and uncompensated status (which will give the capacitor power) and calculate XC and C using the power difference value?