Three Impedances each of (8 - j24)N are connected in mesh across a three-phase 420V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip)

Three Impedances each of (8 - j24)N are connected in mesh across a three-phase 420V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power in a three phase delta system with balanced load is equal to (Sqrt (3)) (VL) (IL) (p.f.) (Sqrt (3)) (Vph) (Iph) (p.f.) (Sqrt (3)) (VL) (Iph) (p.f.) O (Sqrt (3)) (Vph) (IL) (p.f.)
1. Set up the circuit shown using a function generator for the source voltage Vs. Set the function generator to 10 V P-P at 100 Hz (You need to set the Vp-p on the function generator to 5V). Connect the red lead of the scope to VoUT and the black lead to the ground to measure the output or load voltage. 1N4004 Vout Vs 10Vpp 100HZ 1k Ohm 2. Sketch Vout on right, measure the exact peak voltage to the ground on the oscilloscope (use the oscilloscope). DC coupling setting of the 主 Note: Show the results on the screen to your professor to get the signature. V out (Peak) = Vout 3. What is the measured frequency of the load voltage waveform? Frequency f =
(b) A symmetrical three-wire three-phase supply as shown in Figure Q2(b) is connected to a balanced three-phase load. The value of impedance, Z is identified to be 100-j75 Q. (i) Find IaB, IBC and ICa (ii) Determine Iaa, IbB and Ic (iii) Determine Iba, Isb and Ix (iv) Draw the phasor diagram of all currents in Q(b)(i) and Q(b)(ii)
As per bartleby honor code I can submit 3 questions. Please solve b,d and e
If 3-phase transfomer configuration in figure in has the givens as listed below: E-line on high side = 480V, turns ration = 2:1/coil, resistance per load =10, efficienscy = 100%. E/coil on the high side is _____, E/coil on the low side is___, E-phase on the low side is____, E/resitor of the load is____,(a-480v, b-240v, c-120 d-69.28v) I/resitor on the load is____, I-line on the low side is___, I-phase on the low side is____, I/coil on the low side is____(a-2A b-4A c-6.93 d-12A), I-phase on the high side is____, I-line on the high side is____(a-1A b-1.73A c-2A d-4A), Va/phase of the load is____, 3-phase Va on the high side is____(a-120VA b-360VA c-480VA d-1440VA).
1980628cmid 11616 For reactive load, the power factor is equal to Select one: O a. 1 O b. 90 O c. 2 O d.0 If the voltage V, = 800 mV, then the current flowing in the primary winding Ip is: j2on Select one: O a. None of these O b. l, =40<0° mA O c.l, = 0.320<90° A O d. Ip =320<-90° mA if a Load absorbs an average power of 8 kW at a lagging power factor of 0.5 Select one: O a. -8000 + j13856.4 VA O b. None of these O c. 8000 - j13856.4 VA O d. 8000 - j13856.4 VA estion-299141-3 freactive power is
APPLICATION OF IMPEDANCE AND ADMITTANCE IN AC CIRCUIT
2- Draw and explain the phasor diagram for two transformers in parallel.
"As per the standards used in power system, even harmonics are limited to 25 percent of the odd harmonic limits" True False
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.
A source of AC emf E₁ = 120/300 volts with an impedance of Z₁ = 2/0° ohms is connected in parallel with another AC source of E₂ = 120/-30º volts with an impedance Z₂ = 2/90° ohms. The two AC source are use to supply a load impedance of Z₁ = 10/-53.10 ohms. Calculate the value of the load current IL. O a. 7.62 amperes O b. 4.42 amperes O C. 5.38 amperes O d. 6.48 amperes
Q5/C: Compare between Auto transformers and 2 winding transformers.