IL220230°LoadP = 2 kWpf = 0.9 lagAssuming that the source is operating at 60 Hz,determine the following:a.) The value of the current I, in phasor formthe magnitude, degrees for the angle)b.) What is the reactive power Q of the load in(voltsforKVAR?c.) Is the load consuming or supplying Q?d.)What is the apparent power S of the load inKVA?e.) What is the load resistance? Express youranswer in Ohms.f.) What is the load inductance? Express youranswer in millihenries.

e) The load resistance, f) The load inductance.

IL 220230° Load P = 2 kW pf = 0.9 lag Assuming that the source is operating at 60 Hz, determine the following: a.) The value of the current I, in phasor form the magnitude, degrees for the angle) b.) What is the reactive power of the load in (volts for KVAR? c.) Is the load consuming or supplying Q? d.) What is the apparent power S of the load in KVA? e.) What is the load resistance? Express your answer in Ohms. f.) What is the load inductance? Express your answer in millihenries.

IL 220230° Load P = 2 kW pf = 0.9 lag Assuming that the source is operating at 60 Hz, determine the following: a.) The value of the current I, in phasor form the magnitude, degrees for the angle) b.) What is the reactive power of the load in (volts for KVAR? c.) Is the load consuming or supplying Q? d.) What is the apparent power S of the load in KVA? e.) What is the load resistance? Express your answer in Ohms. f.) What is the load inductance? Express your answer in millihenries.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. An alternating current varying sinusoidally with a frequency of 50 Hz has an ms value of 40 A. Find: a. The instantaneous value of 0.0025 seconds after passing through maximum positive value, b. The time measured from the maximum value when the instantaneous current is 14.14 A.
When a load is connected to a power line with a frequency of 230V (rms) 50 Hz, it draws 4500 W at a power factor of 0.80. Find the required capacitance value to increase the power factor to 0.85.
If the voltage and current supplied to a circuit orload by a source are˜VS = 170∠(−0.157) V ˜IS = 13∠0.28 Adeterminea. The power supplied by the source which isdissipated as heat or work in the circuit (load).b. The power stored in reactive components in thecircuit (load).c. The power factor angle and power factor.
When a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3
The following phasor diagram is: a. The phasor diagram of SG when it is running at lagging power factor b. The phasor diagram of SM when it is running at leading power factor c. The phasor diagram of SM when it is running at lagging power factor with the existence of RA d. The phasor diagram of IM when it is running at lagging power factor
Please explain in detail. A. In a series circuit, if the AC voltage is measured across the AC voltage source, will there be any variations in the phase of the AC voltage across each resistor from the measured AC voltage across the source? B. In an AC voltage source, why does voltage vary with time? Please explain in detail. C. In a series circuit, are the frequencies of the AC voltages across each resistor the same? Why is this so? ...
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
A current of 10 A rms results when a single-phase circuit is placed across a 220 V rms source. The current lags the voltage by 60 degrees. Find the power dissipated by the circuit and the power factor.
The rms current in a 33.0-0 resistor connected to an AC source is 2.80 A. (a) What is the rms voltage across this resistor? V (b) What is the peak voltage of the AC source? V (c) What is the average power dissipated by the resistor? W (d) What is the maximum current across this resistor? A
Add the two voltages below together (phasor voltages are RMS). ?ଵ =60 ? ∠ 0° ?ଶ =80 ?∠ 270° a) What is the resultant as a phasor using RMS voltage and degrees? b) What is the resultant voltage as a sinusoidal equation if the frequency is 100 Hz?
What is the average Power at maximum resistance? Why? What is the effect to the voltage and current when increasing the load resistance?