A thread of mecury of capillary tube with uniform cross sectional area closed at one end with the tube vertical and the open and uppermost, the length of the length of the trapped air column is 20cm, calculate the length of air column when the tube is held a.horizontally b.vertically with the open end underneath (ATM 76cm of mecury)

A thread of mecury of capillary tube with uniform cross sectional area closed at one end with the tube vertical and the open and uppermost, the length of the length of the trapped air column is 20cm, calculate the length of air column when the tube is held a.horizontally b.vertically with the open end underneath (ATM 76cm of mecury)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.90P: The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of...

See similar textbooks

Similar questions

Please I need correct solutions to this
As shown in Figure 2.1, liquid of density pis trapped by a gate ABC of unit width into the plane of the page. The gate is hinged at C, and consists of a vertical section AB of length H and an inclined section BC also of length H inclined at an angle with respect to the horizontal. Obtain an expression for the force P required to hold the gate in position. Neglect the weight of the gate and friction in the hinge. Some geometric properties of a rectangle are provided in Figure 2.2, where the symbols have their usual meanings. |6|2 b y + X C Figure 2.1 b N|O 2 Rectangle H H P a Area A = ba 2 C: Centroid a 1xx,c= |yy,c= 1 12 1 12 ·ba³ ab³
Our Subject is FLUID MECHANIC. I need a solution to this problem
1. Two large parallel glass plates separated by a distance d water. The contact angle between the water meniscus and the glass plate is approximately zero. How height will the water rise due to capillary action if the surface tension between water and air is 0.07 N/m? = 1 mm are placed vertically in
Problem 2: An ice cube floats in a glass of water. What fraction of the ice cube lies above the surface of the water? Assume the density of water and ice are 1000 kg/m3 and 920 kg/m3, respectively. m2 A qubo material is submorsod 9 w th
5
11. Find the force exerted on one side of the annular disk shown in Fig. and also locate the center of pressure Water 3m 600 mm
PROVIDE SOLUTION TO THE QUESTION BELOW
H.W: A hypodermic syringe contains a medicine with the density of water. The barrel of the syringe has a cross-sectional area (2.50x10-5) m2, and the needle has a cross-sectional area (1.00x10 8 ) m². In the absence of a force on the plunger, the pressure everywhere is 1.00 atm. A force F of magnitude 2.00 N acts on the plunger, making medicine squirt horizontally from the needle. Determine the speed of the medicine as it leaves the needles tip.
(a) As shown in Figure 2.1, an architect with an artistic flair designs a gate ABC to trap liquid of density pin a canal. The gate is hinged at A and is of unit width into the plane of the page. Section AB of the gate corresponds to a circular quadrant of radius R centred at O. Section BC of the gate is vertical with a height of 2R. The height of the liquid in the canal is R. Neglect the weight of the gate and friction in the hinge. Some geometric properties of a rectangle and a circular quadrant are provided in Figure 2.2, where the symbols have their usual meanings. (i) Determine the magnitude and direction of the horizontal component of the hydrostatic pressure force exerted on the gate by the liquid in the canal. (ii) (iii) Determine the magnitude and direction of the vertical component of the hydrostatic pressure force exerted on the gate by the liquid in the canal. Determine the minimum force F applied at B to prevent the gate from opening (i.e. turning anticlockwise about the…
To find- The magnitude of the horizontal and vertical component of the force exerted by the static fluid on the curved surface.
Solve please. Correct need