A STOP SIGN HANGS FROM A POLE. THE POLE ( AB ) IS MADE UP OF CARBON FIBER AND HAS A LENGTH OF 7.20 METERS LONG IT HAS A MASS OF 12.kg. THE MASS OF THE STOP SIGN IS 21.50 Kg. IF THE CABLE ATTACHED AT THE POLE IS MADE UP OF ALUMINUM. DETERMINE THE TENSION OF CABLE CD AND THE HORIZONTAL AND VERTICAL REACTION OF PIN A RB 37 STOP 3.80 7.20

A STOP SIGN HANGS FROM A POLE. THE POLE ( AB ) IS MADE UP OF CARBON FIBER AND HAS A LENGTH OF 7.20 METERS LONG IT HAS A MASS OF 12.kg. THE MASS OF THE STOP SIGN IS 21.50 Kg. IF THE CABLE ATTACHED AT THE POLE IS MADE UP OF ALUMINUM. DETERMINE THE TENSION OF CABLE CD AND THE HORIZONTAL AND VERTICAL REACTION OF PIN A RB 37 STOP 3.80 7.20

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: .A link in a packaging machine mechanism has a square cross section of 0.40 in on a side. It is…

Q: 26 kip 12 x12 steel plate W 6x15 steel wide- flange beam 12x12 steel plate B. 18 in. square concrete…

A: Compute the hearing stresses at the mating surfaces A, B, C, and D, in Figure

Q: 5.b the diagram below represents the chassis rail of the lorry above. Draw the shear force and…

A: Solution: Given Data: To Find: (a) The shear force diagram. (b) The bending moment diagram.

Q: Whoop- ニフ P:?

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

Q: Problem 4.138 Replace the loading by an equivalent resultant force and couple moment acting at point…

Q: 10 A flat spiral spring is 12 mm wide, 0.3 mm thick and 2.5 m long. Assuming the maximum stress of…

A: A flat spring is 12 mm wide, 0.3 mm thick, and 2.5 m long, as far as we know.The maximum stress of…

Q: The figure below shows two proposed designs of drums to solve the same load and line speed lifting…

A: TWO DIFFERENT ARRANGEMENT OF LOAD HAVING SAME LOAD2.TO DECIDE THE BIGGEST ADVANTAGE WITH DESIGN A…

Q: 4. A small race car has an aluminum hub (shown in red). The drive axle is press-fit into the hub,…

Q: Problem #8: For the beam and loading shown below compute the state of stress at point B (components…

Q: A countershaft carrying two V-belt pulley is shown in Figure 1. Pulley A receives power from a motor…

A: Given: The tension on the loose side of belt, T2 = 0.15T1

Question

Problem 3

A STOP SIGN HANGS FROM A POLE. THE POLE ( AB ) IS MADE UP OF CARBON FIBER AND HAS A
LENGTH OF 7.20 METERS LONG IT HAS A MASS OF 12.kg. THE MASS OF THE STOP SIGN IS
21.50 Kg. IF THE CABLE ATTACHED AT THE POLE IS MADE UP OF ALUMINUM. DETERMINE THE
TENSION OF CABLE CD AND THE HORIZONTAL AND VERTICAL REACTION OF PIN A
RB
37
STOP
3.80
7.20

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Elastic Constants and Their Relationship

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which statement below is incorrect about a shaft in torsion? The angle of twist for a solid tube is proportional to the length of the tube proportional to the torque T inversely proportional to the shear modulus G inversely proportional to the square of its radius
Bolts distributed about a bolt circle are often called upon to resist an external bending moment as shown in the figure. The external moment is 19 kip-in and the bolt circle has a diameter of 15 in. The neutral axis for bending is a diameter of the bolt circle. What needs to be determined is the most severe external load seen by a bolt in the assembly. M Neutral axis R NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. View the effect of the bolts as placing a line load around the bolt circle whose intensity FÅ, in pounds per inch, varies linearly with the distance from the neutral axis according to the relation Fb Fb,max R sin 8. The load on any particular bolt can be viewed as the effect of the line load over the arc associated with the bolt. For example, there are 12 bolts shown in the figure. Thus, each bolt load is assumed to be distributed on a 30° arc of the bolt circle. Under these conditions, what is the largest bolt…
FIGURE PS-66 500 N/m 0.60 m 1 Compute tbe reactions at the supports using the toch niques shown in Section 5-2, 2 Draw the complete shearing force and bending noment dagrams using the techniques shown in Sections 5-3 through 5-8, 3. Determine the magnitude and location of the maximum absolute value of the shearing force and bending moment
Answer in this format. Sketch: Given: Required: Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used)
3. Design Challenge: The wind turbine is designed to generate 2.5 MW of power with the blades rotating at 20 RPM. The large gear has 360 teeth and the small gear has 12 teeth. Design the high speed shaft to minimize weight. That is, choose a material (from your textbook) and cross-section dimensions such that the shaft won't yield, with a safety factor of 2.5, while keeping the shaft's weight to a minimum. Calculate the weight per meter of the shaft you designed. 2 Gear reducer High speed shaft Low speed shaft Generator
Describe the Graphical method for constructing Shear and Moment Diagrams?
Describe the Moment Arbitrarily Applied?
I-section built-in beam in the figure shows two forces It is in effect. These forces at point A and B stress element by finding the stresses that it generates Please show on. Note: force of 100 kN It is in the x-y plane and the point of action is Take as its surface. Force with a magnitude of 180 kN I is in the center of gravity of the section (Search all show transactions and required reductions
Problem 8: Complete the design of the beam shown in figure below to carry a large hydraulic motor. The beam is attached to the two side rails of the frame of a truck. Because of the vertical accelerations experienced by the truck, the load on the beam varies from 1200 lb upward to 5000 lb downward. One-half of the load is applied to the beam by each foot of the motor. Hydraulic motor Side rail of truck Beam to be designed -16 in -50 in 16 in
Determination of vertical displacement of Mid-Term Project pipe assembly Find the vertical displacement at position C in the figure. 800 mm Pipe inner diameter: 40 mm, Pipe outer diameter: 60 mm Material: A-36 Steel 600 N B. -By the force 600N, the AB part of the pipe is subjected to bending and torsional loads. BC part is subjected to bending load. -The energy equation by this load is as follows. Energy equation by torsional load: 400 mm T²dx (U), = 2GJ Problem: Energy equation by bending load a) First, draw a free body diagram and the AB part Of the bending/torsional load of the BC and Derive the bending load equation. So M²dx (U) = 2EI By applying it to the high energy formula, Save energy and make it the same as external energy Release to find the vertical displacement. -The sum of the internal energy of 2 energy is as follows. U=U: +Ub b) Creo modeling and structural analysis -Due to energy conservation, the sum of the internal energy U is the external due to the load 600 NGet the…
Design of Machine Elements Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces appliedto this shaft is given below. What would be length of the shaft considering the conditions as givenbelow;− 40 Nm torque is applied throughout the shaft (torque)− 100 kg load is applied at the end point of the shaft (bending)− 250 kg load is applied to push the shaft in the compression direction (normal force)− Factor of safety should be 2
Q3 The figure shows a round shaft from a gear transmission. Gears are mounted at points A, C, and E. Supporting bearings are at B and D. The forces transmitted from the gears to the shaft are shown, all acting downward. Compute the maximum stress due to bending in the shaft, accounting for stress concentrations. calculate the safety factor for the material selected.if martial 4150 OQT 1300 force 1 (f1)=9.5 kn ,Force 2(f2)=13.5Kn ,Force3 (f3)=18Kn