Answer in this format.Sketch:Given:Required:Solution: (Please answer in detailed (step by step).Indicate labels on what you are doing/performing, for example what formula is used) Consider the steel shaft in the figure as shown. The working stresses are ơw =120 MPa and Tw = 70 MPa. Find the smallest diameter d of the steel shaftthat is capable of carrying the loads shown in the figure. Neglect the weights of thepulleys and the shaft. The pulleys are rigidly attached to the shaft. Assume thatthe stress caused by direct shear force is negligible.MтаxNmTmaxNmHint:Section just to the right of BFrom Mohr's circle1.Construct the bending moment and torque diagram produced by theloadings.2.You'll find out that there will be 2 sections (just to the right of B and C)that will give the largest combinations.3.ОтахkPaπd3Determine the maximum normal and maximum shear stress using theMohr's circle.ТтахkPa4. Compare the maximum normal and maximum shear stresses to theпазallowable stresses.5 Compute for d, and select which d values would be the safest.Section just to the right of CFrom Mohr's circleОтахkPand³ТтахkPand³2500NM'Safest value of d.dтт2500 foLR o.Sm50ON3500L-ROsm

given; ⇒shear stress(τ)=70MPa⇒minimum diameter(d)=?⇒radius(R)=0.5m

Consider the steel shaft in the figure as shown. The working stresses are ơw 120 MPa and Tw = 70 MPa. Find the smallest diameter d of the steel shaft that is capable of carrying the loads shown in the figure. Neglect the weights of the pulleys and the shaft. The pulleys are rigidly attached to the shaft. Assume that the stress caused by direct shear force is negligible. Hint: Construct the bending moment and torque diagram produced by the loadings.

Consider the steel shaft in the figure as shown. The working stresses are ơw 120 MPa and Tw = 70 MPa. Find the smallest diameter d of the steel shaft that is capable of carrying the loads shown in the figure. Neglect the weights of the pulleys and the shaft. The pulleys are rigidly attached to the shaft. Assume that the stress caused by direct shear force is negligible. Hint: Construct the bending moment and torque diagram produced by the loadings.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Keep the same colors the same graph, basically keep everything the same just make the line with a small curve just as shown on the picture Keep everything the same just make the line less curvy please do not change the colors of the line and the circles do not change anything besides the curve of the line. Use this code on MATLAB and fix it. % Sample data for Diesel and Petrol cars carPosition = linspace(1, 60, 50); % Assumed positions of cars % Use the 'seed' function instead of 'rng' seed = 50; % Define your seed here rand('seed',seed); % Assumed CO2 emissions for Diesel and Petrol CO2Diesel = 25 + 5*cos(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Diesel CO2Petrol = 20 + 5*sin(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Petrol % Fit polynomial curves with a reduced degree of 2 pDiesel = polyfit(carPosition, CO2Diesel, 2); pPetrol = polyfit(carPosition, CO2Petrol, 2); % Generate points for best fit lines fitDiesel = polyval(pDiesel, carPosition);…
Posted below is a picture of a data table and a diagram of an experiment. In the experiment you rolled a marble down a ruler ramp off the end of a coffee table to observe projectiles and conservation of energy. You do 3 trials for each initial height. Each height is measured in meters. h= initial height of marble off of table Y= height of table off floor X= horizontal distance marble goes from edge of table to where it strikes the floor a) use the table to find information you need to solve for theoretical range and % of error in measured range.
1) A low-friction cart is placed between two identical springs attached to rigid walls. If you push the cart against one of the springs and release it, it will continue to move back and forth between the springs. www Draw a force-time graph showing the sum of the horizontal forces exerted on the cart as it moves back and force between the springs. Scientific Abilities Is able to construct a force diagram Missing No representation is constructed. Inadequate FD is constructed but contains major errors such as incorrect mislabeled or not labeled force vectors, length of vectors, wrong direction, extra incorrect vectors are added, or vectors are missing. Needs Improvement FD contains no errors in vectors but lacks a key feature such as labels of forces with two subscripts or vectors are not drawn from single point, or axes are missing. Adequate The diagram contains no errors and each force is labeled so that it is clearly understood what each force represents. Explain whether or not this…
The question and data are in pictures. Please answer properly with each steps and explanation. Best of luck. Thank you so much in advance.
|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…
Don't Use Chat GPT Will Upvote And Give Solution In 30 Minutes Please
Hello, please help me. Thank you. Lessons we discussed: Dynamics of Rigid Bodies, Erratic Motion, Rectilinear Motion, Curvilinear Motion, Motion of a Projectile: Normal and Tangential Components. Reminders for you: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. I need the answer right away, thank you. Given Problem: Please see the attached photo.
Lessons Discussed: Dynamics of Rigid Bodies, Erratic Motion, Rectilinear Motion, Curvilinear Motion, Motion of a Projectile: Normal and Tangential Components. Reminder: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. I need the answer right away, thank you. Given Problem: Please see the attached photo.
please sovle part (I) and give me the formulas used in excel Try to find a result less than 50 for the question