Could you please assist with question 5B 5.a the diagram below represents a lorry tail lift. The load represents the maximum loadspecification. Calculate the forces and draw the shear force and bending moment diagramsfor this loading scenario.650 NUDL = 190 N/m4 mThe design specification is for 2 point loads of 350 N, one at 1.5m and one at 3m. calculate theforces and draw the shear force and bending moment diagrams. 5.b the diagram below represents the chassis rail of the lorry above. Draw the shear forceand bending moment diagrams for the maximum load case shown.3 kN3 m4 mThe design specification calls for 2 loads, one of 2 kN at 3.25m from the left and one of 1.5kNat 0.75m from the left. Draw the bending moment and shear force diagrams for this case.

Solution: Given Data: To Find: (a) The shear force diagram. (b) The bending moment diagram.

5.b the diagram below represents the chassis rail of the lorry above. Draw the shear force and bending moment diagrams for the maximum load case shown. 3 m 4 m 3 kN The design specification calls for 2 loads, one of 2 kN at 3.25m from the left and one of 1.5kN at 0.75m from the left. Draw the bending moment and shear force diagrams for this case.

5.b the diagram below represents the chassis rail of the lorry above. Draw the shear force and bending moment diagrams for the maximum load case shown. 3 m 4 m 3 kN The design specification calls for 2 loads, one of 2 kN at 3.25m from the left and one of 1.5kN at 0.75m from the left. Draw the bending moment and shear force diagrams for this case.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
I need these three parts answered, if you are unable to answer all three parts please leave it for another tutor to answer, thank you.
follow up question - for the past two question. (subquestions)
I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal places for magnitude. DO NOT FORGET YOUR UNITS. Enclose all final answers in a box. No need to copy the question or problem. File submissions should be a single PDF. II. PROBLEM SOLVING 1) Given the figures and data below, solve what is being asked for. Y-axis 200mm -200mm 50mm 50mm 100mm 200mm 100mm Y-axis Yo 200mm 100mm 3°1 100mm 547 - ATT HA LO - CHIR →→X-axis -Xo →X-axis
I need question 10 answered please and thank you. Question pertains to the print provided and also the sequence of operations listed in the directions.
Please provide more details for question b and c. thank you
Question 17 Use basic drawing instruments (pencil, scale, protractor, compass, etc.). Using a free-hand sketch, convert this isometric projection to orthographic projection:
*NOTE ON INSTRTUCTUONS AND HINTS
*NOTE ON INSTRTUCTUONS AND HINTS
Question 20 Use basic drawing instruments (pencil, scale, protractor, compass, etc). The Front View of a line AB measures 65 mm and makes an angle of 45° with xy. A is in the H.P. and 15 mm in front of the V.P. The line is inclined at 30° to the V.P. Draw the projections of AB and find its true length and inclination with the H.P.