A stepped shaft ABC consisting of two solidcircular segments is subjected to torques T1and T2 acting inopposite directions, as shown in the figure.The larger segment of the shaft has diameterd1 = 2.25 in. and length L1 = 30 in.; thesmaller segment has diameter d2 = 1.75 in.and length L2 = 20 in. The material is steelwith shear modulus G = 11 x 10^6 psi, andthe torques are T1 = 23,985 lb-in. and T2 =8,117 Ib-in. Calculate the angle of twist inradian at end C.NoteRound up final answer to four decimal placesT1ĮdiT2ВAL2

Answered: Image /qna-images/answer/ef74cdad-e330-44b4-bfd2-0d2a071dfd14.jpg

A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2 acting in opposite directions, as shown in the figure. The larger segment of the shaft has diameter d1 = 2.25 in. and length L1 = 30 in.; the %3D smaller segment has diameter d2 = 1.75 in. and length L2 = 20 in. The material is steel with shear modulus G = 11 x 10^6 psi, and the torques are T1 = 23,985 lb-in. and T2 = %3D 8,117 Ib-in. Calculate the angle of twist in radian at end C. Note Round up final answer to four decimal places T1 T2 В L2

A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2 acting in opposite directions, as shown in the figure. The larger segment of the shaft has diameter d1 = 2.25 in. and length L1 = 30 in.; the %3D smaller segment has diameter d2 = 1.75 in. and length L2 = 20 in. The material is steel with shear modulus G = 11 x 10^6 psi, and the torques are T1 = 23,985 lb-in. and T2 = %3D 8,117 Ib-in. Calculate the angle of twist in radian at end C. Note Round up final answer to four decimal places T1 T2 В L2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in
A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross sectional area of 1cm?; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm? Determine the stress in the rods it p = 6 tonnes.
Q3: Three segments of elliptical solid steel section, circular solid aluminum section and circular solid bronze section were assembled to form the shaft shown in Figure (3). Determine the generated stress in each material when the support at D is able to rotate until 0.035 radian based on the two torques T1 and T2 of 450 N.m and 750 N.m, respectively. 94= 834 v5? AL:28 1 Steel Ahminum Bronze T2 D= 70 mm D= 100 mm 1.5 m 1.5m 2.0 m 25 mm Figure (3) 145 mm
An inclined plate 2 m long and 1 m wide lies with its length inclined at 45° to the surface of water and the nearest edge 1 m below it. If the specific weight of water is 1000 kg/m³, then calculate the total pressure on the plate (in kg).
5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. A D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB-10KN-m Tc=15KN.m
Bar A has diameter 'd' and bar B has diameter '2d'. Both are of the same length and are of the same material. If they are subjected to same axial load P, the ratio of extension of bar A to B is (B) 2 (A) 4 (C) 0.5 (D) 0.25
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
The plate has a thickness of 20 mm and the force P = 5 kN acts along the centerline of this thickness such that d = 150 mm. (Figure 1) Figure d‡ 200 mm a 1 of 1
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; α = 2.9 × 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; α = 12.5 × 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.2. The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 56 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1).
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 × 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 × 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 69 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft 07.01 kips 5.63 kips 8.39 kips 9.29 kips 6.66 kips (1) B 3 ft C 8 ft 1.5 ft
The tubular shaft shown in the figure has an external diameter of D = 5.5 in. and an internal diameter of d = 2.75 in. and is subjected to a torque of T= 6825 lb-in. [theta = 31 deg] What is the shear stress at A?in psi What is the shear stress at B?in psi What is the shear stress at C? What is the shear stress at D?in psi What is the shear stress at E?in psi