A solid rotating shaft made of Annealed AISI 1030 is used in a boat with a high speed as shown in the figure. The transmitted power is 224 KW with Revolutions number 130 rpm. Use the failure criteria to determine the shaft diameter and which one is more conservative. Take n=1 and endurance limit 18.86 Kpsi. Man to 100 mm 9.75 m

A solid rotating shaft made of Annealed AISI 1030 is used in a boat with a high speed as shown in the figure. The transmitted power is 224 KW with Revolutions number 130 rpm. Use the failure criteria to determine the shaft diameter and which one is more conservative. Take n=1 and endurance limit 18.86 Kpsi. Man to 100 mm 9.75 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B5
Time left 0:23: The driveshaft of an automobile is being designed to transmit 196 kW at 3177 rpm. Determine the minimum diameter (in mm) required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 27 MPa. Note: Do not include units in your answer Torsion: J=d 32 T 3=1 / J 0 = TL≤ GJ Jo = # (do"-di") Jot P = Tw 32 Answer: Next page
42. The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find the value of the critical speed. Shaft is steel. Ans. n = 1810 rpm. Design of Shafts Chap. 3 248 t. 50 30 1"dia 10" 10" Figure 3-52 Problem 41. 10 kg 10 kg C B 375 600 mm 375 Figure 3-53 Problem 42.
Only HAndwritten answer please
Quickly please
A mild steel shaft has to transmit 75 kW at 200 rpm. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the shaft and keys 40 N/mm²Shear stress for bolts = 28 N/mm²Shear stress for C.I. coupling = 20 N/mm² Take wearing stress as twice the shear stress value and number of bolts for coupling as 6.
Q5: A steel cantilever shaft.The fillet is 6 mm, Sut= 560 MPa and Sy= 420 MPa. Assume the shaft surface is cold-rolled, operating temperature is 550c, reliability is 50%. Calculate the design safety factor Nfusing Good-Man theory of failure. R6 400N |$25 600N 500N 250N 200mm For the stepped rod shown which is acted upon by both a fluctuating axial force (F1) of between - 900 N and 3,600 N and a constant axial force (F2) of 2,250 N, determine (a) The factor-of-safety (Nf) using the Goodman theory. The stepped rod is made of high-strength steel, ground to the dimensions shown. The stepped rod operates at room temperature. Known that the ultimate stress 735 MPa, yield stress 500 MPa and k=1.15. d = 0.48 cm d = 0.32 cm F, F2
A solid steel shaft is to be designed to transmit 700 kW at 1,500 revolutions per minute. The steel selected is a AISI 1030, hot rolled steel. The shaft is 1 mm long. Assume that the bending load on the shaft is negligible. Using a factor of safety of 1.5, design the diameter of the shaft.
None
The solid steel rotating shaft in the figure is supported at B and C, and is driven by a gear, not seen, which is linked to spur gear D which has a pitch diameter of 150 mm. The drive gear force F acts at a pressure angle of 20 degrees. The shaft transmits a torque to point A of Ta-350 N.m. The properties of machined steel shaft are Sy-420 MPa and Sut-560MPa. Use a safety factor of 2.5 and determine the minimum allowable diameter in section B and C. Assume sharp felt radii at the bearing shoulders to estimate the stress concentration factors.Explain.
Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm
Q5: A steel cantilever shaft.The fillet is 6 mm, Sut= 560 MPa and Sy= 420 MPa. Assume the shaft surface is cold-rolled, operating temperature is 550c, reliability is 50%. Calculate the design safety factor Nfusing Good-Man theory of failure. R6 400N ф25 600N 500N 250N 200mm For the stepped rod shown which is acted upon by both a fluctuating axial force (F1) of between - 900 N and 3,600 N and a constant axial force (F2) of 2,250 N, determine (a) The factor-of-safety (Ni) using the Goodman theory. The stepped rod is made of high-strength steel, ground to the dimensions shown. The stepped rod operates at room temperature. Known that the ultimate stress 735 MPa, yield stress 500 MPa and k=1.15. d = 0.48 cm d = 0.32 cm F, F2