Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at “N” rpm. from a turbine generating n electric motor to a compressor. The service factor may be assumed as 1.35. The following permissible stress may be used: Shear stress for shaft, bolt and key material = 40 MPa Crushing stress for bolt and key = 80 MPa Shear stress for cast iron = 8 Mpa Speed N in Rpm = 200 Power P in kN = 16

Q: In a thrust bearing, the external and the internal diameters of the contacting surfaces are. 19 mm…

A:

Q: 3= Q + & 4qAnrm & Expert Q&A Design a shatt and tiange tor a Diesel engine in which protected type…

A: A flange coupling is a driving connection between rotating shafts that consists of two flanges, one…

Q: From previous Figure 1, fill in the table given. (No need to show calculation step) (Hint: Output…

A: The output torque is To. The output speed of pulley is N=150 rpm. The diameter of the shaft is given…

Q: 3. A flat annular steel flywheel of outer radius 0.5 m and inner radius 0.125 m with p = 7800…

A:

Q: Design a muff coupling to connect two shafts transmitting 42 kW at 130 rpm. The permissible shear…

A: Answer: ◆ Design of shaft: Shaft diameter is 90 mm ◆ Design of muff: Outer diameter is 195 mm Length…

Q: A drive shaft is made of a hollow tube with an outer diameter of Do 2.5 in. It is desired to…

A:

Q: Q/A rigid type flange coupling are connected two shafts made of plain carbon steel. The shafts are…

A: Given   Shear stress = 60 MPa        Power, P = 25 kW       Speed, N = 500 rpm Find   Diameter, d

Q: As seen in the figure, a construction machine is rotated by a drive mechanism consisting of…

A:

Q: G+ Figure 5 (b) The diameters of shaft AB and CD in Figure 5 are 50 mm and 75 mm, respectively. The…

A:

Q: = It is required to design a split muff coupling to transmit 60 kW power at 140 rpm. The shafts, key…

A: Step 1:Calculating Shaft Diameter :The power transmitted by the shaft can be related to the torque…

Q: h Thoist, Phoist 11 m mg G=5 Gear box Pshaft Tshaft, Pshaft Electrical machine 400 V 50 Hz Tower…

A: For the solution refer below images.

Q: Answer this ASAP plz A double row angular contact ball bearing is used in the engine compressor to…

A:

Q: Calculate the pressure between a shaft with an outer diameter of 0.034 m and an inner diameter of…

A:

Q: (3) A flange coupling is to connect two 60mm shafts. The hubs of the coupling are Ø120mm, 100mm…

A:

Q: campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km=…

A:

Q: The value of curvature correction factor k, will be if the spring index is 6. O a. 1.33 O b. 1.08 O…

A:

Q: terial of piston rings Grey cast ird wable tensile stress = wable radial pressure on cvlinder = 0.03…

A:

Q: A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of 1-…

A: Power is given by P =( T * n )/63025  T = F*D/2 Ssy = 0.577*Sy ( distortion energy theory)

Q: A propeller shaft rotating at constant speed is subjected to variable loads.Ball bearing supporting…

A:

Q: Give the suitable dimensions of a leather open flat-belt system according to the standards having…

A: Belt drives are used to transfer power from one shaft to another using pulleys that rotate at the…

Q: A jaw clutch for a 4 3/16 in shaft has three jaws with radial forces. The inside diameter is 4 3/8"…

A: Given DataPw=6000psidi=438'do=1112'jaws=2clutch=4316'jaws=3

Q: The client requires a single step up spur gearbox to transmit a 10kW power from a shaft rotating at…

A:

Q: esign a clamp coupling to transmit ‘35’ kW at ‘120’ r.p.m. The allowable shear stress for the shaft…

A: GivenPower P=35kWN=120rpmτshaft=τkey=50MPanumber of bolts n=6The permissible tensile stress for the…

Q: find the torque for an IC engine:- mrod= 0.3 kg. Lord =200 mm. Cg of rod at 60 mm from crank pin…

A: Given…

Q: (b) (c) Calculate the hoop tension, Fe due to centrifugal force. b Find the torque, T due to the…

A: DefinitionHoop tension:Hoop tension, also known as hoop stress, is the stress that develops in the…

Q: Calculate the shaft diameter necessary to support a combined maximum bending moment of 2000 Nm, and…

A:

Q: endurance limit can be calculated for static and dynamic load in shaft design Select one: True False

A: endurance limit can be calculated for static and dynamic load i shaft design  false

Q: A double row angular contact ball bearing is used in the engine compressor to accept radial loads of…

A: Given Data:- Fr=6000N Fa=3000N RPM=2400rpm

Q: A (25 kW, 500 rpm) motor has a mild steel shaft of (30 mm) diameter and (8 cm) length. There are two…

A:

Q: Q4/A 40 kw power at 300 rpm is transmitted from 50 mm diameter shaft by means of two identical…

A: Given data: Power transmitted by the shaft (P) = 40 kW Speed of the shaft (N) = 300 rpm Diameter of…

Q: Consider the belt drive having a diameter of 150 mm that is mounted on the overhung end of a shaft,…

A: Given: The diameter of belt drive, d' = 150 mm = 0.15 m The overhang length, x = 30 mm = 0.03 m The…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.