A small barrel weighing 400 N is lifted by a pair of tongs as shown. Knowing that h = 200 mm, L₁ = 400 mm, L2 = 120 mm and L3 = 200 mm, determine the magnitude of the forces exerted on memberABD of this machine structure.CL2APL1L3BDReport your answers in units of N with 2 decimal places of precision.N.The magnitude of the force acting at joint B =The magnitude of the force acting at joint D =N.

Answered: A small barrel weighing 400 N is lifted…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The simply supported beam is built up from three boards by nailing them together as shown. The applied force is P = 14.9 kN The nails are each able to resist a shear force of 1 9 kN Part A Determine the maximum allowable spacing of the nails.. Express your answer to three significant figures and include appropriate units. 8= HÅ Value Units ? I m 100 mm 25 mm- . 332 1 1 m 25 mm 200 mm. 25 mm
In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a clockwise moment of 340 lb in about point A. (Figure 1) Figure A == 18 in. 30° 5 in. 114 1 of 1 Part A Determine the required magnitude of force F. Express your answer with the appropriate units. μÅ F = Submit Value Provide Feedback Request Answer Units ?
Three solid cylindrical rods are welded together to form the compound axial member shown in the figure. The compound axial member is attached to a fixed support at A. Each rod has an elastic modulus of E = 47 GPa. Use the following values for the rod lengths and areas: L₁ = 1350 mm, L₂ = 1760 mm, L3 = 1300 mm, A₁ = 260 mm², A₂ = 155 mm², and A3 = 80 mm². What magnitude of external load Pis needed to displace end D a distance of up = 30 mm to the right? Part 1 8₁ F₁ = Part 2 8₂ F2 A = L₁ mm/kN (1) B L2 (2) Find the relationship between ₁, the elongation of rod (1), and the internal tensile force, F₁, in rod (1). Assume 8, is a positive value in units of mm and F, is a positive value in units of kN. So, the answer you enter for the ratio (8₁/F₁) must be in units of (mm/kN). mm/kN C L3 (3) D Similar to the previous step, find the relationship between 82, the elongation of rod (2), and the internal tensile force, F2, in rod (2). Assume 82 is a positive value in units of mm and F2 is a…
Please help, I promise to give good feedback. Please do not just guess. Thank you!
Round the answer into 3rd SIGNIFICANT DIGIT!Round the Answer into 3rd SIGNIFICANT DIGIT! Round the answer into 3rd SIGNIFICANT DIGIT!Round the Answer into 3rd SIGNIFICANT DIGIT!
125 N 90 mm 240 N x 30mm B D A 75 mm 60 mm 150 N 50 mm 300 N x A machine component is subjected to the forces shown, each of which is parallel to one of the coordinate axes. Replace these forces with an equivalent force-couple system at A.
Pleas was wet the question I keep getting the wrong answer
The force of F = 55 lb acts along the edge DB of the tetrahedron shown in (Figure 1). Figure 8 ft 10 ft 6 ft 4 ft 15 ft F 1 of 1 B Part A Determine the magnitude of the moment of this force about the edge CA. Express your answer in pound-feet to three significant figures. MAC = Submit Provide Feedback VAΣo↓ vec Request Answer lb. ft
Show complete and detailed solution. Draw illustrations
The beam in (Figure 1) is made from three boards nailed together as shown. Part A If the moment acting on the cross section is M = 560 N- m. determine the maximum bending stress in the beam. Express your answer to three significant figures and include appropriate units. HÁ Omax = Value Units igure 1 of 1> Submit Request Answer 25 mm Provide Feedback 150 mm 20 mm 200 mm M 20 mm
I need correct answer
The 62-mm-diameter steel shaft is subjected to the torques shown. (Figure 1) Figure 1 of 1 400 mm B 3 kN.m 600 mm 2 kN-m I GILM Determine the angle of twist of end A with respect to C. Take G=75 GPa. Express your answer to three significant figures and include the appropriate units. A/C= Submit μA Value Units My Answers Give Up ?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS