A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T= i MPa

A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T= i MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problems 2. Mild Steel is tested in the laboratory. The data obtained are: Length of Specimen = 320 mm / Diameter of Specimen = 30 mm / Elongation under a load of 20 kN = 0.055 mm Load at Yield Point = 130 kN Maximum Load = 210 kN Load at fracture = 115 kN Length of Specimen at failure = 380 mm Diameter of Specimen at failure = 17.5 mm Calculate (1).Young's Modulus (2). Yield Stress (3). Ultimate Stress (4). Fracture Stress (5). % Elongation (6). % Reduction in Area.
2. Consider a bar of AISI 1015 cold-drawn steel. Using the distortion-energy and maximum-shear-stress theories to determine the factors of safety for a stress state with the following plane principal stresses: 04 = 30 kpsi, OB = 15 kpsi.
Question 3: The 60 mm diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the absolute maximum and minimun shear stresses on the outer surface of the shaft and specify their locations, measured from the fixed end A. Take : AA= 1.6 BB = 0.9 CC = 1200 AN/ m 2 kN-m/m AA m CC Nm B вB m Solution : = CC N-m TAB CC N-m 2o0ox N.m CC N.m
Please Follow this Properly, I Like your answer Structure, Accuracy, Concept, Please No submit Handwriting.
Required Information For a bar of AISI 1015 cold-drawn steel, determine the factor of safety using the distortion-energy and maximum-shear- stress theories for the following principal stresses. A = 28 kpsl, and og = 15.5 kpsi The factor of safety from the maximum-shear-stress theory is 1.94 1.88 and the factor of safety from distortion-energy theory is
The hollow ACB shaft made of steel has an inner diameter of 40 mm and an outer diameter of 50 mm and is fixed against rotation at the A and B ends. As shown in the figure of a rod welded vertically to the shaft at point C of the shaft, P forces are applied to the ends in the horizontal direction. If the maximum allowable slip on the ACB shaft is 45 MPa, determine the largest value of the P force. stretching
I need the answer as soon as possible
The principal stresses at a point inside a solid object are ơ1 = 100 MPa, 02= 100 MPa and 03= 0 MPa. The yield strength of the material is 200 MPa. The factor of safety calculated using Tresca (maximum shear stress) theory is n, and the factor of safety calculated using von Mices (maximum distortional energy) theory is ny.
A strain gauge mounted at a potentially critical point in a steel part has recorded the stress history shown below during 20 seconds of typical use. Identical parts have been fatigue tested under constant amplitude loading with R = -1 to give an endurance limit of 60 ksi and a fatigue strength of 140 ksi at N = 1000 cycles. The steel used has an ultimate strength of 165 ksi. Estimate the fatigue life of the part under typical use. How much will the fatigue life in problem 3 (above) be reduced if a mean stress of 10 ksi is added to the stress history given?
A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and firmly attached. The diameter d1 = 70 mm and the diameter d2 = 90 mm. Brass G = 39GPa and steel G = 77.20 GPa. Determine: The torque that can be applied if the deformation at one end is 10 degrees. Answer: T = 8.64 kN – m The torque that can be applied if the maximum shear stress in brass is 70MPa and in steel is 110MPa. Answer: T = 6.352 kN – m Recommendation: analyze by segments. The first segment is only brass, then the composite part between brass and steel, and the last part only steel. In the composite segment, use only one material. In this same segment, equalize the deformations.
A machine element is subjected to the following bi-axial state of stress; sigma x = 80 MPa; sigma y = 20 MPa; Txy=40 MPa. If the shear strength of the materials is 100 MPa, find the factor of safety as per Tresca's maximum shear stress theory.
Find the R ratio for this cyclic loading Asap otherwise skip it