A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross-sectional area of 1cm2; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm2. Determine the stress in the rods if P = 6 tonnes. 2m 2 1:5m 3 Im-D5m P

A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross-sectional area of 1cm2; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm2. Determine the stress in the rods if P = 6 tonnes. 2m 2 1:5m 3 Im-D5m P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q-5: For the element with stresses as shown below, find: a. The magnitudes and directions of major and minor principal stresses b. The shear and normal stresses acting on a horizontal plane as shown below 8kPa 2kPa 75° 75° экра TH Jon OH 4kPa 30° Horizontal plane
number 4 only
The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam causes the end A to be displaced 7.5 mm downward. The wires are unstretched when the beam is in horizontal position. Figure 3 m 2 m -2 m 1.5 m E 1 of 1 2 m ▼ Part A Determine the normal strain developed in wire CE. Express your answer in millimeters per millimeter to three significant figures. ECE = Submit Part B E AD = Submit D Provide Feedback AEO Ivec Request Answer Determine the normal strain developed in wire AD. Express your answer in millimeters per millimeter to three significant figures. AE Ivec S ? Request Answer mm/mm ? mm/mm
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a= 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 31 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft O 3.74 kips 4.77 kips (1) B 3 ft 8 ft 1.5 ft 2 D
It is made of solid circular cross-section bars, whose geometry and loading condition are given in Figure 2. The system formed is made of steel material and the torsional moments is under the influence. The diameter of the AB part of the rod is 100 mm; The diameter of the BC part is 60 mm. the shear modulus of steel is G = 80000 MPa. a)Draw the torsional moment diagram of the rod. b)Calculate the maximum shear stress that will develop in the system. c)Calculate the relative rotation value of point C with respect to point A b. M2 (kN.m) M1 (kN.m) B. A 100 mm 60 mm C а-а b-b L3 (mm) L4 (mm) kesiti kesiti Şekil 2 M1 (kN.m) M2 (kN.m) L3 (mm) L4 (mm) 60 50 600 700
The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the figure. 6mm thick steelThe tank is manufactured by joining the plate with a helical weld at an angle of 30°. parallel to the weld seamSince the safe shear stress in the direction is 30 MPa, the maximum pressure that can be used in the tank is determined.calculate.
The nut on a bolt is tightened by applying a force of P = 18 lb to the end of a wrench at a distance of a = 7.0 in. from the axis of the bolt. The body of the bolt has an outside diameter of d = 0.425 in. What is the maximum torsional shear stress in the body of the bolt? Answer: Tmax i a psi
Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a 22-mm-square bar of alloy and the load P is 20.15 kN. Express your answer in two decimal places.
Situation 5 A steel shaft with a constant diameter of 50 mm is loaded as shown by applied torque. Use G=83 GPa. Solve for the total angular deformation. 800 N-m 1300 N-m 1200 N-m 2 m 1.5 m 3 m
At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 12.5 x 10-6/°F] and bar (2) is stainless steel [a = 7.3 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 33m B (2) Answer: Final temperature = 55 in. -0.06. gap °F.
Problem 3 For the compound beam shown in Figure 4, determine the reaction forces, calculate the stress in each member, and determine the deformation in each beam using the Direct Stiffness Method. 3 ft 2 ft 2 ft y 500 lb 300 ft-lb 1= 0.948 in ¹ E = 30 106 psi I = 0.198 in ¹ E = 30-106 psi
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 38 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft 5.16 kips 4.86 kips 2.48 kips 3.88 kips O 4.09 kips (1) B 3 ft P 8 ft 1.5 ft