A rigid bar AB is supported by three rods. A load P = 375 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10^6 kN/m^2 and modulus of elasticity of steel is 200 x 10^6 kN/m^2.a. Determine the deformation in the rods (in mm). 8. A rigid bar AB is supported by three rods. A load P = 375 kN is applied to thebar. The modulus of elasticity of copper is 110 x 10^6 kN/m^2 and modulus ofelasticity of steel is 200 x 10^6 kN/m^2.Steel rodA = 900sq. mmSteel rodA = 900sq. mm2 mCopperA = 1200sq. mm2 mAB1m1m

Answered: Image /qna-images/answer/288af543-b4a3-48d7-8352-75f667fd250f.jpg

A rigid bar AB is supported by three rods. A load P = 375 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10^6 kN/m^2 and modulus of elasticity of steel is 200 x 10^6 kN/m^2. a. Determine the deformation in the rods (in mm).

A rigid bar AB is supported by three rods. A load P = 375 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10^6 kN/m^2 and modulus of elasticity of steel is 200 x 10^6 kN/m^2. a. Determine the deformation in the rods (in mm).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The light rigid bar ABCD shown is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P = 30 kips is applied.
Steel bar of cross-section 550mm2 is acted upon by the forces shown in figure. For steel, E = 200GPa. Compute the stress in BC Compute deformation of AB Compute the total elongation of the assembly.
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
The rigid bar is supported by a smooth pin and two rods as shown. Neglect the weight of the rigid bar. The assembly is initially stress-free. Determine the stress in each rod if the temperature increases by 25°C after a load W = 100 kN is applied. The steel rod has an area of 320 mm² with a = 11.7 um/ ( m°C ) and E = 200 GPa. For the bronze rod, it has an area of 1380 mm? with a = 18.9 µm/ ( m°C ) and E = 83 GPa. Bronze | 3 m Steel | 1.5 m 1.0 m - - 2.5 m +1.5 m→
Determine the normal stress in members BD, AC, and BCin the truss shown. The cross-sectional area of each member is 1500mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value.
The steel bars are firmly attached to rigid supports. Initially the temperature is 840F. Determine the stress in bars AC and CB when the temperature becomes -600F. Use E = 29 x 106 psi and α = 6.50 x 10-6/ 0F.
3. The rigid bar ABC is pinned at B and attached to the two vertical rods. Initially, the bar is horizontal and the vertical rods are stress-free. Determine the stress in the steel rod if the temperature of the both rods is decreased by 30°C. Neglect the weight of bar ABC. Steel L=0.9 m A 300 mm E= 200 x 10 N/m' a= 11.7 um/(m C) Aluminum L=1.2 m A = 1200 mm E = 70 x 10 N/m a= 23 pum/(m "C) Answer: Ost B 0.6 m 1.2 m
Please solve it ASAP and with all the steps and please solve it urgently and please solve all the parts as well please The strains at a point in a plate subjected to plain stress were measured as: Use this information to find the stresses in an element at the same location that is rotated 30 degrees counterclockwise and draw your results.
Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The dimensions of the block are as follows: L_x=100 mm,L_y=30 mm,L_z=40 mm. Determine the change in length along the y-axis. Use E = 200 GPa and v 0.3. Note that ɛ_0=-o/E(1+2v). A -0.03 mm -0.015 mm -0.009 mm -0.012 mm
Q2. Two members of Aluminium AB and BC are connected as shown in the Figure Q2.Point A is a fixed end support, point B is a pin connection and point C is a pin support. The cross section of member AB is 120 x 120 mm and member BC is a rod of 120 mm diameter. A forced P is applied to the connection B. Given the young modulus, E = 70 kN/mm² for both members. (a) Prove that both members are slender (Member is slender when the slenderness ratio, λ >90) (b) Determine the maximum load, P that can be carried by the structure. (c) Determine the allowable load, P if the factor of safety is 3.0. 4m P KN B 2m 2m 1m
Q1