A strain gauge is mounted to the outer surface of a thin-walled boiler, as shown in Figure. The boiler has an inside diameter of 2,600 mm and a wall thickness of 25 mm, and it is made of stainless steel [E=193 GPa; v=0.27]. Determine - (a) the internal pressure in the boiler when the strain gauge reads 196 pe. b) the maximum shear strain in the plane of he boiler wall.

A strain gauge is mounted to the outer surface of a thin-walled boiler, as shown in Figure. The boiler has an inside diameter of 2,600 mm and a wall thickness of 25 mm, and it is made of stainless steel [E=193 GPa; v=0.27]. Determine - (a) the internal pressure in the boiler when the strain gauge reads 196 pe. b) the maximum shear strain in the plane of he boiler wall.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Steel Tank with an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used as storage of gas under pressure of 2.2 MPa. a. Determine the value of the tangential stress in the tank wall Determine the value of the longitudinal stress in the tank wall b. 30 mm helt hand
Stress
The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the figure. 6mm thick steelThe tank is manufactured by joining the plate with a helical weld at an angle of 30°. parallel to the weld seamSince the safe shear stress in the direction is 30 MPa, the maximum pressure that can be used in the tank is determined.calculate.
Question # 2: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. 2 m a a 0.5 m 400 KN 100 mm 1 300 mm 100 mm Section a-a
An 8-mm thick steel tank has an outside diameter of 600 mm. It is internal pressure of 2.40 MPa. Determine the maximum subjected to stress in the tank. an
A solid aluminum (E = 70 GPa] rod (1) is connected to a solid bronze (E = 93 GPa] rod (2) at flange B, as shown. Aluminum rod (1) has an outside diameter of 34 mm and bronze rod (2) has an outside diameter of 16 mm. The normal stress in the aluminum rod must be limited to 139 MPa, and the normal stress in the bronze rod must be limited to 103 MPa. Assume L1 = 166 mm and L2= 359 mm. Determine: (a) the maximum downward load P that may be applied at flange B. (b) the deflection vg (downward is positive) of flange B at the load determined in part (a). C L2 B P. (1)
Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m
Two wooden studs with cross-sectional dimensions 45×145 mm2 are glued together to form a beam with a T-sectionaccording to the figure on the right and loaded according to the figure on the left. The beam is loaded in its rigiddirection.a) Calculate the moment of inertia of the cross-section about the centroid axis (z-axis).b) Calculate the maximum normal stress in the beam.c) Sketch the normal stress distribution over the most loaded cross-section of the beam. All calculations must be clear and handwritten, draw and check so that the answers are correct
The cross section of the AB part of the welded pipe part given in the figure is a hollow pipe and the cross section of the BC part is a circle with a solid body. The inner diameter of the pipe section is 20mm and the outer diameter is 28mm, while the diameter of the full body part is 12mm. Determine the average normal stress at the D and E points accordingly.
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 13 mm, and a length of 5.5 m. The pipe supports a compressive load of 600 kN. After the temperature of the pipe drops 39°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD = mm mm
The assembly shown in figure below consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is touch to its support. A 0.75 m Steel A = 250 mm E = 200 GPa *i* O 1.5 m Aluminum L = 2m A = 300 mm' E = 70 GPa B D
Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m