@ A rectangular footing 2.0 x 2.5 m in dimensions is located at a depth of 1.0 m below the ground surfaces and it is subjected to inclined load of 550 kN as shown in figure 2. The groundwater level is 1 m below the ground surface. Determine the gross allowable bearing capacity for a factor of safety of 3 using general equations. Is foundation safe? Y-16 kN/m³ Ys=19kN/m² c=15 kN/m² ஓ=25 550 kN 2.0 X 2.5 m Figure (1) N.GL Figure (2) 1.0m

@ A rectangular footing 2.0 x 2.5 m in dimensions is located at a depth of 1.0 m below the ground surfaces and it is subjected to inclined load of 550 kN as shown in figure 2. The groundwater level is 1 m below the ground surface. Determine the gross allowable bearing capacity for a factor of safety of 3 using general equations. Is foundation safe? Y-16 kN/m³ Ys=19kN/m² c=15 kN/m² ஓ=25 550 kN 2.0 X 2.5 m Figure (1) N.GL Figure (2) 1.0m

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Mat Foundations

Section: Chapter Questions

Problem 10.1P: Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The...

See similar textbooks

Similar questions

Redo Problem 16.13 with the following data: gross allowable load = 184,000 lb, = 121 lb/ft3, c = 0, =26, Df = 6.5 ft., and required factor of safety = 2.5. 16.13 A square footing (B B) must carry a gross allowable load of 1160 kN. The base of the footing is to be located at a depth of 2 m below the ground surface. If the required factor of safety is 4.5, determine the size of the footing. Use Terzaghis bearing capacity factors and assume general shear failure of soil. Given: = 17 kN/m3, c = 48 kN/m2, =31.
A 2.0 m 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c = 0, = 26, = 19 kN/m3, and cu = 60 kN/m2. Determine the maximum possible value for Q, considering short-term and long-term stability of the footing.
A 2.0 m 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c = 0, =26, = 19 kN/m3, cu = 60 kN/m2 (=0 condition). Determine the maximum possible value for Q, considering short-term and long-term stability of the footing.
A flexible circular footing of radius R carries a uniform pressure q. Find the depth (in terms of R) at which the vertical stress below the center is 20% of q.
Repeat Problem 5.1 with the following data: B = 1.5 m, L = 1.5 m, Df = 1 m, H = 0.6 m, = 35, c = 0, and = 15 kN/m3. Use FS = 3. Refer to Figure 5.2 and consider a rectangular foundation. Given: B = 1.5 m, L = 2.5 m, Df = 1.2 m, H = 0.9 m, = 40, c = 0, and = 17 kN/m3. Using a factor of safety of 3, determine the gross allowable load the foundation can carry. Use Eq. (5.3).
Repeat Problem 11.1 based on limit state design, using the factors given in Table 11.4. 11.1 A continuous foundation is required in a soil where , , and . The depth of the footing will be 1.0 m. The dead load and the live load are 600 kN/m and 400 kN/m, respectively. Determine the required width for the foundation based on allowable stress design with FS = 3, using Eq. (6.10) and Table 6.1.
Redo Problem 7.6 using Vesic’s (1975) solution [Eq. (7.12)]. 7.6 A 2.0 m wide continuous foundation is placed at 1.5 m depth in a saturated clay where cu = 40 kN/m2 and γ = 18.5 kN/m3. At 2.0 m below the ground level, this clay layer is underlain by a stiffer clay where cu = 60 kN/m2 and γ = 19.0 kN/m3. What would be the maximum wall load allowed with FS = 3? Use Eq. (7.11).
Redo Problem 6.2 using the general bearing capacity equation [Eq. (6.28)]. A 5.0 ft wide square footing is placed at 3.0 ft depth within the ground where c = 200 lb/ft2, = 25, and = 115.0 lb/ft3. Determine the ultimate bearing capacity of the footing using Terzaghis bearing capacity equation and the bearing capacity factors from Table 6.1. What is the maximum column load that can be allowed with a factor of safety of 3.0?
Redo Problem 16.2 using the modified general ultimate bearing capacity Eq. (16.31). 16.1 A continuous footing is shown in Figure 16.17. Using Terzaghis bearing capacity factors, determine the gross allowable load per unit area (qall) that the footing can carry. Assume general shear failure. Given: = 19 kN/m3, c = 31kN/m2, =28, Df = 1.5 m, B = 2 m, and factor of safety = 3.5. Figure 16.17 6.2 Refer to Problem 16.1. If a square footing with dimension 2 m 2 m is used instead of the wall footing, what would be the allowable bearing capacity?
The applied load on a shallow square foundation makes an angle of 15 with the vertical. Given: B = 1.83 m, Df = 0.91 m, = 18.08 kN/m3, =25, and c = 23.96 kN/m2. Use FS = 4 and determine the gross allowable (vertical component) load. Use Eq. (16.9).
Refer to Problem 16.1. If a square footing with dimension 2 m 2 m is used instead of the wall footing, what would be the allowable bearing capacity? 16.1 A continuous footing is shown in Figure 16.17. Using Terzaghis bearing capacity factors, determine the gross allowable load per unit area (qall) that the footing can carry. Assume general shear failure. Given: = 19 kN/m3, c = 31kN/m2, =28, Df = 1.5 m, B = 2 m, and factor of safety = 3.5. Figure 16.17
Refer to Figure 5.2. Given: B = L = 1.75 m, Df = 1 m, H = 1.75 m, = 17 kN/m3, c = 0, and = 30. Using Eq. (5.6) and FS = 4, determine the gross allowable load the foundation can carry.