A rectangular block is 104 mm long in the X direction, 77 mm wide in the Y direction, and 60 mm thick in the Z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 200 kN tension in the X direction, 193 kN tension in the Y direction, and 225 kN compression in the Z direction. If v = 0.3 and E- 191 GPa, determine the single uniformly distributed load in the X direction that would produce the same deformation in the Z direction as the ariginal loading. Answer must be in kN.

A rectangular block is 104 mm long in the X direction, 77 mm wide in the Y direction, and 60 mm thick in the Z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 200 kN tension in the X direction, 193 kN tension in the Y direction, and 225 kN compression in the Z direction. If v = 0.3 and E- 191 GPa, determine the single uniformly distributed load in the X direction that would produce the same deformation in the Z direction as the ariginal loading. Answer must be in kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A concrete dam has the profile shown in Figure If the density of concrete is 2400 kg/m³ and that of water is 1000 kg/m³, determine the maximum compressive if the depth of the water behind the dam is h = 15 m. stress at section m-n 3 m 1 25 m h 9 m
A structural steel bar with a 25 mm × 75 mm rectangular cross section is subjected to an axial load of 150 kN. Determine the normal stress in the bar.
A rectangular column of sides 0.4 m × 0.35 m , made of concrete, is used to support a compressive load of 2800 kN. Four steel rods of each 24 mm diameter are passing through the concrete as shown in figure. If the length of the column is 3 m, Esteel=200 GPaEconcreate=29 GPa a)determine the normal stress in the concrete b)determine the normal stress in the steel.
Show your detailed , clear, and complete solution. Thank you.
A flat annular steel disc of 0.8 m outside diameter and 0.15 m inner diameter is to be shrunk around a solid steel shaft. The shrinking allowance is 1 part per 1000. Neglecting shaft expansion, determine: (a) The stress in the system at standstill. (b) The speed at which the shrink fit will loosen as a result of rotation. Material density is 7800 kg/m³; Poisson's ratio is 0.3; Young's Modulus is 210 GPa; [108.68 MPa: 4300 rpm
The extruded plastic shape has dimensions of D = 31 mm, d = 25 mm, a = 93 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 375 N. (b) If the allowable shear stress for the plastic material is 1550 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? D d A a Answer: (a) TA = kPa (b) V =
Given an element with stresses as indicated in the figure, answer the following questions. (1) The major and minor principal stresses and the planes on which they act. (2) The max. shear stress and the inclination of the plane on which it acts.
Q.3.L
Answer the questions given the following stresses: d) The value of the shear stress at any plane inclined at any angle with the horizontal is e) The value of the normal stress at any plane inclined at any angle with the horizontal is
Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a uniform thickness of 5 mm and a yielding stress of 250 MPa, determine the force F that initiated the yielding of the fillet section. a.1.25 kN b.2.5 kN c.4 kN F d.2 kN 40 mm 25 mm 40 mm ↓ Which of the following is FALSE regarding the equation for deformation, 8=PL/AE? A. The term AE refers to the resistance of the member against axial deformation B.It can be used even for non-prismatic members C.It can only be used to compute for the elastic axial deformation of the member D. The term P refers to the internal axial force at the section considered A rigid bar ABC is loaded and supported as shown in the figure. After the load P is applied, the deformation of bar BD, SBD 0.6mm. What is the displacement at point B? A.0.36 mm B.0.48 mm P C.0.75 mm D.1.00 mm C 0.3 m 0.3 m Which of the following statements is TRUE for a circular shaft under pure torsion? A. The angle of twist of a point on the…
A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at top of the beam section at midspan where the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 263 mm Beam height = 455 mm Uniform load = 6.9 kN/m Span of the beam = 12 m Prestressing force = 359 kN eccentricity = 115 mm
For the stress case given in the figure, approximate the principal plane (in degrees).