The figure below shows the cross-section of a concrete column, encased in 8.2mm thick steel. The column is 5.5m high and carries an axial load of 8.6MN. If Econcrete = 14 GPa and Esteel = 200 GPa, calculate:| 3.1 3.2 The stress in the steel and concrete The change in length of the column 855 concrete 8,2mm thick steel 715

The figure below shows the cross-section of a concrete column, encased in 8.2mm thick steel. The column is 5.5m high and carries an axial load of 8.6MN. If Econcrete = 14 GPa and Esteel = 200 GPa, calculate:| 3.1 3.2 The stress in the steel and concrete The change in length of the column 855 concrete 8,2mm thick steel 715

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flat annular steel disc of 0.8 m outside diameter and 0.15 m inner diameter is to be shrunk around a solid steel shaft. The shrinking allowance is 1 part per 1000. Neglecting shaft expansion, determine: (a) The stress in the system at standstill. (b) The speed at which the shrink fit will loosen as a result of rotation. Material density is 7800 kg/m³; Poisson's ratio is 0.3; Young's Modulus is 210 GPa; [108.68 MPa: 4300 rpm
The reinforced concrete beam has the cross-sectional area shown in the figure with b =12 in., d=16 in., ? steel= 1.571 in.2, determine the largest bending moment that may be applied safely. Takethe elastic moduli ?steel=29(10^3) ksi and ?concrete= 3.6(10^3) ksi. The working stresses are2.39ksi for concrete and 22.145ksi for steel.
Question 1 a) A square concrete column in an office building is shown below. The column has cross section of 400mm x 400mm and supports a total vertical load of 2000KN. Calculate the direct compressive stress at any point in the column. If the column reduces in length by 3.5 mm, the loading and the column's original length was 4 meters. Calculate; i. The strain ii. Stress iii. Young modulus in the column.
1. Determine the following: a. Determine the moment of inertia of the section about its neutral axis. b. Maximum tensile stress in the beam c. Maximum compressive stress in the beam 300 N/m 625 mm T: 100 mm 500 mm A B 3 m 1.5 m 100 mm
The concrete column (300 mm x 300 mm) is reinforced by four steel bars each having diameter of 30 mm as shown in Figure Q1. The working stresses for steel and concrete are 200 MPa and 25 MPa, respectively. Determine the largest axial force P that can be safely applied to the column. Use Est - 200 GPa and Eco = 20 GPa. Dimensions in mm 300 300
No long explanation needed. Solve in 3 decimal places. Write the complete solutions and Diagrams. Box the final answer.
A rectangular concrete beam 277 mm wide and 495 mm deep is simply supported over a span of 8.37 m. the beam is reinforced with straight tendons situated 59 mm above the bottom of the beam under a prestressing force of 387 kN. Concrete weighs 23.36 kN/m3 with modulus of elasticity Ec=13,814.76 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads. (Include the sign if it is negative) Please avoid rounding off values during the course of solution proper as much as possible. Always write your answer in 4 decimal places
A rectangular concrete short column is shown in the figure below. If Pis 80kN, ey and ex is 30mm, determine the stress at all corner of the section and illustrate the distribution of stress in the section graphically. ( where CC= b=500mm ; BC=h=750mm) bst Gp 3
A reinforced concrete beam experiences a load as shown. It has a base of 350 mm, and an effective depth of 600 mm, with 4 – 25 mm diameter rebars. The concrete has a compressive strength of 27.6 MPa, Determine the maximum distributed load that the beam can carry. Assume that the allowable stress in steel is 167 MPa (instead of 160 MPa). w 1.5 m 10 kN 1.5 m 5 m
A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 279 lb/ft over its 22.3- ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel. Round off the final answer to two decimal places. ... 6 in. 10 in. 1/2 in. -b-
An axial load P is supported by the short steel column shown in the figure. The column has a cross-sectional area of 14,400 mm2. If the average normal stress in the steel column must not exceed 69 MPa, determine the minimum required dimension a (in mm rounded to the nearest tenths) so that the bearing stress between the base plate and the concrete slab does not exceed 8 MPa. Assume b = 400 mm.
An IPE 330 × 160 carries the load shown below. Compute the stress due to bending. 110 kN 44 KN 44 KN 2 m 2 m 0.75 m 0.75 m