A prestressed concrete rectangular beam of size 300 x 900 mm is prestressed with an initial prestressing force of 700 kN at an eccentricity of 350 mm at midspan, stress at top fibre at midspan due to prestress alone is : 1. 3.46 MPa (tension) 2. 8.64 MPa (compression) 3. 2.59 MPa (compression) 4. Zero

A prestressed concrete rectangular beam of size 300 x 900 mm is prestressed with an initial prestressing force of 700 kN at an eccentricity of 350 mm at midspan, stress at top fibre at midspan due to prestress alone is : 1. 3.46 MPa (tension) 2. 8.64 MPa (compression) 3. 2.59 MPa (compression) 4. Zero

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pre stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.
Question A pre-stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.
USE NSCP 2010 A reinforced rectangular concrete beam has a width of 250 mm and aneffective depth of 360 mm. It is reinforced for tension only at the bottomwith a total tension steel area of 600 mm². fc’ = 40 MPa, fy = 400 MPa. a. Determine the tension reinforcement index for this beam.b. Determine the distance of the neutral axis below the compressionsurface. c. Determine the ultimate flexural strength of the beam.
The total compressive force at the time of failure of a concrete beam section of width 'b' without considering the partial safety factor of the material is (a) 0.36 fok b Xu (c) 0.66 fok b Xu (b) 0.54 f b Xu (d) 0.8 f b X, ck where X, is the depth of neutral axis, f cube strength of concrete. ck
Problem 2 A reinforced concrete beam is 300 mm wide with an effective depth of 400 mm. Use fe= 21 MPa and fy = 415 MPa. The section is reinforced with 5- 028mm bars. 1. Determine the stress in the tension steel. 2. Determine the total tensile force in the steel at nominal strength. 3. Calculate the nominal flexural strength of the section.
Asap
3.) A reinforced concrete beam 300 mm width has an effective depth of 450 mm. it is reinforced with 6-32mmØ at the tension side and 2-28 mmØ at the compression side located at 65 mm from the top. f= 34.5 MPa and fy 345 MPa. Assume all steel yield and the contribution of compression steel may not be neglected. (NSCP 2001) a. Find the balanced steel ratio in percent? = b. Find the depth of compression stress block. c. Find the nominal moment capacity of the beam.
21. The column of reinforced concrete is loaded with P = 8000 lbs. The modulus of elasticity (E) is 4.2E6 psi and the Poisson ratio is 0.15. 16in 16in What is the normal stress along section b-b? a. -15.625 psi b. -7.81 psi c. -2.60 psi d. -11.04 psi
Situation C: A rectangular beam has a concrete strength of 24 MPa. The yield strength of the reinforcing bars is 300 MPa. Width of the beam = 350 mm. %3D 65 mm 2 - 25 mm e 435 mm 5 - 36 mm e 350 mm 7. What is the depth of compression block in mm?
The maximum compressive stress in a beam is 6 MPa. The depth of neutral axis of the beam is 60 mm and the compressive strength of the concrete used is 30 N/mm2. Determine the effective curvature of the beam.
A beam has a flange width of 810mm and a slab thickness of 50mm. The width of the web section is 300mm and it has an effective depth of 550mm. It is reinforced at the bottom with a steel area of 1750mm2. fc’ = 20MPa, fy = 400MPa. The magnitude of the compressive force of concrete is ____kN
Subject: Reinforced concrete Design- Civil Engineering A simply supported rectangular beam has a width of 300mm and the distance to the centroid of tension reinforcement is 330mm. The tension reinforcement has an area of 2463mm.2 and the area of compression reinforcement placed 70mm from the compression face of the beam is 1231.5mm.2, fy = 415MPa, fc'=30MPa, balanced steel ratio of 0.031.The design strength using 0.90 as the reduction faction is Choices A. 282kN.m B. 245kN.m C. 254kN.m D. 228kN.m