Problem 5 The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20000 psi? the ¾ in diameter pin is in double shear. NS: P = 19770 lb-f A 10 in. B 30° P 12 in.

Problem 5 The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20000 psi? the ¾ in diameter pin is in double shear. NS: P = 19770 lb-f A 10 in. B 30° P 12 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 35 kN. Assume that a = 240 mm,…

A: Given Data Determine the average shear stress in the pin-B.

Q: Problems: Analyze the rigid frame given below using either the Portal Method or the Cantilever…

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

Q: A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness…

Q: (6) The tension member is fastened together using two bolts, one on each side of the member as…

Q: A plate is fastened to a fixed member by four 20-mm diameter rivets arranged as shown. Compute the…

Q: Link BD consists of a single wooden member 37.5 mm wide and 21.3 mm thick. Knowing that each pin has…

Q: the largest axial P force that the given riveted joint can safely carry. calculate. Rivet diameter…

Q: Determine: a. Cross sectional area of the members b. Internal load in member AB, and indicate if…

A: a. Cross-sectional area of the members Since each member has a semi-circular cross-section with a…

Q: The uniform 2Mg bar is supported by a smooth wall at A and by a pin at B. Determine the diameter of…

Q: C- ODD: Assume that the axial load P = 40kN applied to the lap joint is distributed equally among…

Q: A force P = 70 kN is applied at the plate-bolt connection shown. Determine the required diameter in…

Q: A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN…

A: Given:- The magnitude of the force (P) = 4.5 kN The dimension variable (b) = 240 mm = 0.24 m The…

Q: Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure.…

Q: iven: -The members are a semi circular cross section with a radius of 16mm -Thickness of each…

Q: The bolt in the figure below is 1 in. in diameter. If the load P is 10 kips, determine the average…

A: Given-Bolt diameter= 1 inchLoad, P=10kips

Q: D CED Front view 18 mm 6 mm B B Side view 160 mm 120 mm A Top view In the steel structure shown, a…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

Q: The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450mm².…

A: 3 suspended bars are given, of equal cross-sectional area as shown in the figure above and it has…

Q: 170 소 30 14 Ölçüler mm cinsindendir. A-A kesiti When the torture in the figure squeezes the…

A: Force, F=P=1 kN=1000 N Hogging Moment, M=1000×70=70000 Nmm Consider the cross-section of the section…

Q: the largest axial P force that the given riveted joint can safely carry. calculate. Rivet diameter…

A: B = 340 mm t1 = 21 mm t2 = 38 mm Rivet diameter = 28 mm Shearing stress of rivet = 1400 kg/cm²…

Q: Compute the maximum force P (lb) that can be applied by the machine operator, if the shearing stress…

A: The given figure is shown below:

Q: A force P = 85 kN is applied at the plate-bolt connection shown. Determine the required diameter in…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: The lap joint shown is fastened by five 34 inch-diameter rivets. The bearing stress in the plates is…

A: Given data : Diameter of rivets d = 34 in , Thickness of each plate is t = 12 in , Bearing stress…

Q: Determine the nominal strength for tensile yielding in the gross section. 1. B. 429.67 KN D.390.10…

Q: -4 in 1 in Вох 2 Shear Flow: la A T-shaped beam is made by attaching two 1 × 4 in boards using nails…

A: To Find :- Shear Stress at Neutral Axis Shear Flow at the joint

Q: The safety stress for the steel bar shown in the figure is ϭallow= 160MPa. According to the…

A: Solution:

Q: Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt…

A: We have to find out the unit stress in each bolt with the given data,

Q: Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum…

A: Given that: E = 200 GPa

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: Calculate the value of P using both shear stress criteria and angle of twist criteria. The criteria…

Q: 31, a = 5, b = 4, and c = What is the location of zero shear from A in meters? Given: w = 2. w kN/m…

Q: The lap joint shown is fastened by five ¾ inch-diameter rivets. The bearing stress in the plates is…

Q: 5. The lap joint shown is fastened by two %-in.- diameter rivets. Calculate the maximum safe load P…

A: (As per student demand, Solution to 5 ) To find:Calculate the maximum safe load P

Q: The safety stress for the steel bar shown in the figure is σallow= 160MPa. According to the greatest…

A: Solution:

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

Q: 06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50…

Q: A A. The weight of the crate B. The internal force in rod AC 60° -60° C For the figure above, rods…

Q: A 1 2-inch diameter solid round steel bar must transmit a torque of 6000 in-lb and another moment…

A: If the force can cause the deformation of a material by slippage along the plane or parallel to the…

Q: With

Q: Question 3 A compressive force of 45 kN acts parallel to the longitudinal axis of the I-section as…

Q: 7. (c) A load P of 5000 Kg on the crank pin of the crank shaft as shown in figure is required to…

Q: The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute…

A: Torsion is the stress caused due to torque generated by force acting. It is a shear force generated…

Q: Consider the truss structure and the loading given below. a) Compute the average axial stress on…

A: Take equillibrium at point B to find force

Q: "1-80. Determine the maximum allowable torque T that can be transmitted by the joint. The shear pin…

A: Given:- The diameter of the shear pin is 25 mm The failure shear stress of the material (τtail) =…

Q: Part A The beam shown in the figure below (Elgure 1) is subjected to a moment of M 10 kN m.…

A: KINDLY NOTE: As per our guidelines, we are supposed to answer the first question, in case multiple…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Problem 5
The right-angle bar is supported by a
pin at B and a roller at C. what is the
maximum safe value of the load P that
can be applied if the shear stress in the
pin is limited to 20000 psi? the 3/4 in
diameter pin is in double shear.
ANS: P = 19770 lb-f
A
10 in.
B
30°
P
12 in.
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

T'he pin is made of a material having a failure shear stress of Tail = 100 MPa. Determine the minimum required diameter of the pin to the nearest mm. Apply a factor of safety of F.S. = 2.5 against shear failure. %3D 80 kN
A Single rivet lap joint is to commect 12 mm thick plates by providing 20mm dia. rivet at so mm pitch. determine the strength of the joint and joint efficiency. Take working stress. in shear in rivets = 80N/mm², working stress in beaning in rivets = 250 N/mm² and working stress in axial tension in plates = 150 N/mm².
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
The assembly shown below is pinned at A & C and A & C are subjected to a double shear. Let each pin diameter be 18 mm, and P = 20 kN. Find the:a) Force at the rod BC (kN) and force acting on pin A (kN)b) Average shear stress at A (MPa), and average shear stress at C (MPa)
Please answer the questions on the picture and draw free-body diagram make sure you show all of your work, Thank you for your help!
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P
F5. The circular shaft AC is fixed to rigid walls at A and C. The section AB is solid annealed bronze and the hollow section BC is made of aluminum alloy 2024 T-4. There is no stress in the shaft before the 20,000 ft-lb torque is applied. Determine the maximum shearing stress in each shaft after T is applied. Section BC 4 D=4" 20 ft-k 6.5-FE B 5ft Match each item to a choice: TAB TBC 2"
The shown L-shape cantilver is loaded as shown and fixed at A. It has a constant section of 40 mm X 20 mm. For point I located at 50 mm from support A, at the midheight of the section, determine the principal stresses, the principal planes and the maximum shear stress. y 50 mm 150 mm 40 mm 0.5 kN H- I 20 mm 3 kN 160 mm 2.5 kN
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
Answer 15&16