Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub

Q: A tubular aluminum alloy [G = 4,000 ksi] shaft is being designed to transmit 480 hp at 1,600 rpm.…

A: Given values:Power, P = 480 HPSpeed, N = 1600 rpmG = 4000 ksi = 576000 kip/ft2Maximum shear stress,…

Q: For the below shaft, knowing that T= 36 kip.in, The modulus of rigidity for the Steel and the…

A: It is parallel combination of shaft, so there is no relative motion between them. Angle of twist in…

Q: tubular aluminum alloy [G = 4,000 ksi] shaft is being designed to haft must not exceed 7 ksi, and…

A:

Q: A tubular aluminum alloy [G= 4,000 ksi] shaft is being designed to transmit 480 hp at 2,700 rpm. The…

A: Power, P = 480 HP Speed, N = 2700 rpm G = 4000 ksi = 576000 kip/ft2 Maximum shear stress, τmax= 6…

Q: The Link AB must be made of steel with a maximum normal stress of 450 Mpa. Any stress above that…

A:

Q: The 50-mm diameter circular rod creates in the metal sheet a shear stress through section AC and BD.…

A:

Q: B D 3 600 lb

A:

Q: Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A:

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

A:

Q: Question 3 Part a: For the section shown, determine the: • Maximum elastic Moment M Fully plastic…

A: Given Dataσy=250 MN/m2E=200 GN/m2We are supposed to calculate the following parameters.Maximum…

Q: 1.0 m 3.3 m A simple pin-connected truss is loaded and supported as shown. All members of the truss…

A:

Q: 2. The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

A:

Q: pls help ASAP absolute value of torential sheer stress of the hollow steel Two circular shafts are…

A:

Q: The rigid platform shown has negligible mass and rests on two steel bars, each 250 mm long. The…

A: For the given rigid platform,

Q: A flanged bolt coupling consists of ten 16-mm-diameter bolts spaced evenly around a bolt circle 650…

A: Given data,    No of bolts = 10 Diameter of bolt (d) = 16 mm Diameter of bolt circle = 0.650 m…

Q: A plate is fastened to a fixed member by four 20-mm diameter rivets arranged as shown. Compute the…

A:

Q: Link BD consists of a single wooden member 37.5 mm wide and 21.3 mm thick. Knowing that each pin has…

A:

Q: Determine: a. Cross sectional area of the members  b. Internal load in member AB, and indicate if…

A: a. Cross-sectional area of the members  Since each member has a semi-circular cross-section with a…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A:

Q: A Single rivet lop joint is to comment 12 mm thick plates by providing 20mm dia. rivet at so mm…

A: Answer  We are given thickness of plates = 12 mm Nominal diameter of rivet ϕ = 20 mm Pitch p = 50 mm…

Q: A machine member is subjected to forces as shown in Fig. B 300- 3 kN-m 1.5 kN-m 20 kN Determine the…

A: A )  To find : Determine the stresses ? A problem of solid mechanics.

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: Given :

Q: A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN…

A: Given:- The magnitude of the force (P) = 4.5 kN The dimension variable (b) = 240 mm = 0.24 m The…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A:

Q: 1. Assume that the diameter of the rivet that joins the plates is d = 20 mm. The working stresses…

A: To find out the minimum safe thickness of the plate.

Q: A tubular aluminum alloy [G = 4,000 ksi] shaft is being designed to transmit 350 hp at 1,900 rpm.…

A: a tubular aluminium  alloy  G=4000 Ksi shaft  is being designed to transmit a power P=350 hp at…

Q: 2. The lap joint that is 130 mm wide and 25 mm thick is connected by three 20-mm-diameter rivets.…

A: Given, d=20 mm Number of rivet n=3 Allowable shear stress = 65 MPa Bearing stress =45 MPa Maximum…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A:

Q: Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A: to find stress in each rod

Q: Q-A hollow shaft of external and internal diameters as 100 mm and 40 mm respectively is transmitting…

A: Given Internal diameter Di = 40 mm Outer Diameter Do =100 mm Number of revolution per minute N = 120…

Q: d help wirh 3 and

A:

Q: A joint connection is shown below. If the average shear stress in the pin must not exceed 107 MPa,…

A: Given: Max. shear stress = 107MPa, D=12mm = 12*10-3 Ma. applied load, P= ?

Q: The safety stress for the steel bar shown in the figure is  ϭallow= 160MPa. According to the…

A: Solution:

Q: The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed…

A:

Q: A tubu being The m.

A: G=4000ksi L=7ft N=1800rpm P=490hp to find Dmin

Q: 1. The solid aluminum shaft ABCD caries the three torques shown. (a) Determine the smallest safe…

A:

Q: Ends A and D of the two solid steel shafts AB and CD are fixed, while ends B and C are connected to…

A: Hi! Thank you for the question As per the honor code, We’ll answer the  questiononly in typed…